Search results

Materials and Methods Samples from C-Mn steel with 6 mm thickness were machined to become 2 mm thickness in gage length, parallel to the rolling direction, was used on this study (Fig. 3) and the detailed composition is given in Table 1.
Lal, ”Steady State Plane Strain Cold Rolling of a Strain Hardening Material”, Journal of Material Processing Tech., no. 52, 1995, p. 338 [4].
Journal of Mechanical Sciences, no. 41, 1999, p. 1401 [5].
Geir , “Yield function calibration for orthotropic sheet metal based on uniaxial and plane strain tensile test,” Journal of Material Processing Technology, no. 186, 2007, p. 221 [9].
Vacher., “Full-field measurement technique and its application to the analysis of materials behaviour under plane strain mode,” Materials Science and Engineering A, no. 500, 2009, p. 47

But EDM has a low material removal rate and a severely damaged surface layer.
Latanision: Materials Science and Engineering A, Vol.198(1-2) (1995),pp. 25
Luis: Materials Processing Technology, Vol.143-144 (2003), pp. 521
[3] Shervani-Tabar and Mohammad T.: International Journal of Advanced Manufacturing Technology, Vol.32(2007), pp.719
Villa: Journal of Materials Processing Technology, Vol.164-165 (2005), pp. 889.

Cladding of a hard material onto relatively softer materials for enhancing its wear resistance is a common industrial practice.
Materials and experimental The clad layers were made by Plasma Transformed Arc method with using EUTRONIC GAP 200 by CASTOLIN equipment.
Elsevier applied science; London 1988
Santos, Pulsed current plasma transferred arc hardfacing, Journal of Materials Processing Technology 171 (2006) 167–174 [7] A.S.C d`Oliveira., R Vilar, C.G.
Papadimitriou, Failure analysis of stellite dies for brass extrusion: The effect of aging; Journal of Materials Processing Technology 182 (2007) 608–614 [11] S.

Recently research in visible light response has focused on materials like such as CdS [26], CdSe [27] and PbS [28].
Therefore, Cd-Pb free alternative materials were present.
Material and Methods Materials and Chemicals.
Quan: Materials Research Bulletin Vol.49 (2014), p. 223
Lee: Materials Science and Engineering: C Vol. 27 (2007), p. 1343 [17] H.

Electromagnetic forming is a kind of processing technology that use lorentz force to make rapid prototyping of metal workpiece, which can significantly improve the metal forming performance,and it is expected to become an emerging technology that alternative to traditional machining to process light alloy materials.
Basic principle of electromagnetic forming Field forming process of pulse high magnetic field is a complicated physical field coupling issue, involving many other disciplines such as the electromagnetic field, structure field, temperature field and material science.
Conclusion Electromagnetic forming process is a complicated physical field coupling problem, which involves the electromagnetic field, structure field, temperature field and material science, and other disciplines.
Acknowledgement This work is supported by Science and Technology Foundation of Hubei Provincial Department of Education (Q20141202) and State Key Laboratory of Advanced Electromagnetic Engineering and Technology (Huazhong University of Science and Technology).
Journal of Materials Processing Technology, 1998, 75: 6-16.

An alternative materials that exhibit improved magnetic features classified by a principle MFe2O4 where M indicates the metal (Cu2+, Mg2+, Zn2+, Co2+, Ni2+, Cr2+, etc.).
Nanoparticles of metal oxide are one of the best important novel materials target resistant microorganisms [17].
Materials and Methods Fe (NO3)3·9H2O) - Iron (III) Nitrate (SDH-USA), Cobalt (II)–nitrate {Co (NO3)2·6H2O}, Crist Purisino Germany, Citric Acid (C6H8O7·H2O) - (Romil Pure Chemistry, UK), ammonia solution (NH4OH) – Msccles field, Cheshire, UK).
El Danaf “Assessment of Photodynamic Therapy and Nanoparticles Effects on Caries Models” Journal of Medical Sciences, 6 (2018) 289-1295
Shokrollahi, “The role of cobalt ferrite magnetic nanoparticles in medical science”.

As the second generation of composite materials for armor, AFRP is widely used in military, aerospace and automobile industry.
There are just little fibers remained on machined surface so that the friction between materials and the tool is reduced.
The Properties and application of aramid fibers and the composite materials [J].
Materials and Manufacturing Processes: 1993, 8(6): 631-651
Journal of Manufacturing Science and Engineering, 2002, 124(4): 778-783

Experimental materials The basic composition of high carbon chromium bearing steel was shown in Tab. 1.
Materials and Design, 27(2006), p: 58-63
Materials Science and Technology, 1989, 5(12): 1207-1211
Journal of Materials Science and Technology, 1998, 14(2): 104-108
The second phase in steel materials[M].

Materials and methods Materials.
Polymer materials Science and Engineering, Vol. 25(2002), p. 115 [2] B.
Chemical Journal of Chinese University, Vol. 28(2007), p. 2006 [7] Deyun Ji, Zhengying Liu, Xiaorong Lan.
Chemical Journal of Chinese University, Vol. 27(2006), p. 2193 [9] Xiaolang Chen, Yang Xu, Zhidan Sun.
Chemical Journal of Chinese University, Vol. 33(2012), p. 2092

Arrangement on reinforcing steel in pile section Test Materials.
The materials of slide bed and slide body were loess from the south suburb of Xi'an.
Test I: when using double-layer plastic films as slide surface material, the main resistance was the friction between plastic films.
Journal of Soil and Water Conservation, China, 1991,5(02):14~21 [3] Y.H.Zeng,M.X.Zheng:Force Distribution Rule of Retaining Piles with Prestressing Cables.Journal of East China Jiaotong University, China, 2003,20(2):15~18 [4] W.J.Lei,Y.R.Zheng,G.X.Wang et al:Mechanism Analysis of Slope Reinforcement with Deeply Buried Piles with Model Test, Chinese Journal of Geotechnical Engineering, China, 2007, 26 (7):1347-1355
Journal of Engineering Geology, China, 2009. 17(5): 669~671 [8] X.C.Li,Y.M.Men,G.Y.He:Test research on strata resistance of pile side of anchor anti-slide pile.