Search results

The instrumented falling weight impact (IFWI) tests have been performed on a Ceast Fractovis IFWI tester equipped with a Ceast DAS 8000 data acquisition system according to EN ISO 6603-2.
With increasing irradiation doses, the ILSS of the composite has increased by 11% to the dose of 50 kGy, after that a slight decrease could be observed, which can lead to the assumption, that between 50 and 100 kGy the dominance of the beneficial effect of the increase in crosslinking density has been changed to the negative effect of the reduction of chain segment lengths of the epoxy matrix.

According to the influencing factors and availability of data, combing with the main problem existing in the Yangtze River Delta, indices was composited with three aspects in this paper: Economic development (shown in Table 1), Social development (shown in Table 2), resources and environmental press (shown in Table 3).
So they should take the new urbanization road: optimizing and upgrading the industrial structure, energy-saving and emission reduction should be considered.

In addition, the hydroforming technology increases production efficiency with high quality and reduces wasters, resulting in the enhancement of economic benefit and the reduction of manufacturing cost [2,3].
The properties for the Al 5083 tube were obtained from the tensile test with the following data: E=69GPa, γ=0.33, K=480GPa, n=0.4, σs=145MPa, σb=290MPa.

(9) γ as a reduction factor is introduced here considering the influence inner defects, and equals 0 /γ λ in which 0γ equals 0.3 for non-prestress and partial prestressed steel, and 0.5 for full prestressed steel.
Results Comparison Between Test and Limit Analysis 0.00E+00 2.00E+05 4.00E+05 6.00E+05 8.00E+05 1.00E+06 1.20E+06 1.40E+06 NPW5-L5 NPW5L10 NPW7L15 HPW5-L5 HPW5L10 HPW7L15 FPW5-L5 FPW5L10 FPW7L10 FPW7L10B FPW7L15 FPW7L15B Shear Failure Load (N) Test Results Ultimate Analysis Results Fig. 3 Solution of x of FR-W5-L5 Beam Fig. 4 Data Comparison Conclusions To assume SFR-UHPCC as modified Coulomb material is relative reasonable.

In addition, modern detection and sensing technology, display technology, control technology , data transmission and system theory research, especially in computer science achievement for detection process digital, intelligent to create the conditions , not only to promote electrical measurement and the instrument itself change, but also they add a lot of new growth point [5].
[3] Jong-kyu Jung, Woo-seub Youm, Kyi-hwan Park, “Vibration reduction control of a voice coil motor (VCM) nano scanner,” International Journal of Precision Engineering and Manufacturing, vol.10, no.3, pp.167-170, 2009

The surfaces of the Ni mold and processed PI samples were observed by optical microscopy (OM) and scanning electron microscope (SEM) and their morphological data such as the structure dimensions were measured using an interferometric surface profiler (Zygo New View 5000).
The shear viscosity (V) showed the same tendency with G', and it was decreased with the increase of temperature, showing a sharp reduction started before Tg.

X-ray diffraction (XRD) data were collected using Cu-Kα radiation with a X'part APD X-ray diffractometer (Philips).
String reduction of the magnetic resonance signal intensity of the liver parenchyma in the T2-weighted sequences was found 10min after intravenous application.

As discussed in [5], there needs a correction for the reduced Young’s modulus relating to the reduction of the elasticity of a perforated panel which reduces the natural frequency of the panel.
More data are required to support this finding.

It was noted that an external vibrator was used to facilitate the compaction, and the air bubble reduction of the slurry in the mold.
The data acquisition system was Instron 5500R type digital electrohydraulic servo testing machine (Instron co.

These data prove that the UV-0 chains are grafted onto CS successfully.
The probable reason may be that an introduction of UV-0 functional monomer destroyed the regularity of the molecule chains of chitosan, resulting in the reduction of crystallinity.