Search results

Four moulds were made by a CO2/silicate sand molding process with sand grain size of 151 according to the AFS standard.
Fig. 2 demonstrates the number of graphite nodules as a function of cast sample thickness.

So in the global calculation: • Separate the iteration number n into odd and even
In the future the model will be extended to low temperatures and to incorporate bcc materials and grain boundary effects.

Introduction Metallic conductivity and good electrocatalytic properties enabled the use of ruthenium oxide as a promising electrode material for a number of applications, which resulted in commercial fabrication of so-called dimensionally stable anodes for chlorine generation in the chlor-alkali industry [1,2].
For RuOxHy/XC 46 composite (Fig. 1b), a single phase is seen, consisted of large, more than 15 µm in size, irregular grains.

The beginning of the ferrite growth is seen on the /G γ interface on the limited number of graphite nodules.
It is seen, that the growth starts on the αγ interface and on the boundary of the austenite grains (Fig.6c, Ch8).

Table1 Fly ash technology index and grades Serial number Technology index Grades Ⅰ Ⅱ Ⅲ 1 Fineness is no more than(μm) 12 20 45 2 Loss on ignition is no more than (%) 5 8 15 3 Water requirement is no more than (%) 95 105 115 4 Sulfur trioxide content is no more than (%) 3 3 3 5 Water content is no more than (%) 1 1 Not stipulating Class Ⅰand Ⅱ fly ashes are high quality, which are especially suitable for preparation of pumping concrete anti-seepage, mass concrete, impermeability structural concrete, sulfate resistant concrete and soft water erosion resistance of concrete and underground, underwater engineering concrete, grouting of concrete and roller-compacted concrete.
Sand When the requirements of Class II sand are satisfied, good gradation river sand should be given priority to select, since river sand is relatively clean, contains small amount of clay and relatively large amount of quartz grains in the sand, which generally meet the requirements.

The selection of checker bricks needs to comprehensive consider all kinds of factors such as the thermal efficiency and the effective utilization ratio of the checker chamber, service life of checker bricks and so on, not the more number of holes and the smaller aperture of checker bricks the better.
It can be achieved that the suppression of NOx generated in burning and blasting process through reasonable control of hot stove dome temperature; to strengthen the isolation protection of the hot blast stove shell by brushing acid-resistant coating material and gunning acid-resistant gunning material on high temperature zone stove shell; to use fine grain steel plate as stove shell material and take heat treatment measures to eliminate or reduce the welding stress during manufacturing process; to make the hot blast stove high temperature zone stove shell insulation and take other protective measures to prevent the occurrence of hot blast stove shell intergranular stress corrosion; to extend hot blast stove campaign life and achieve synchronization with the campaign life of BF.

Alloy Tg（K） Tx（K） ΔTx（K） Cu60Zr20Ti20 707.65 743.39 35.74c Cu54Zr22Ti18Co6 711.05 756.87 45.82 Cu50Zr25Ti15Co10 715.99 773.19 57.20 Cu50Zr22Ti18Ni6Co4 702.52 777.02 74.50 A large number of bulk glassy alloys which have high glassy forming ability fit the three criteria proposed by A.
From the chemical viewpoint, for Cu50Zr25Ti15Ni10 bulk glassy alloy, the effect of corrosion resistance is as below: (1) Homogenous: The homogenous of amorphous include two parts, first is the structure, there is no defect such as grain boundary, twin, lattice defect, dislocation and stacking fault; second is the composition, due to the rapid quenching during solid process, there is not enough time for atom to diffuse, so the appearance of second phase, precipitate and segregation is prohibited[12,13].

It was found that Ms of Co, Al codoped sample is more significantly enhanced, indicating that the FM of the sample may be derived from the increase of the carrier concentration.[13] Ferromagnetism is due to oxygen vacancies A large number of studies also confirmed that the oxygen vacancy is also essential for the generation of ferromagnetism.
Moderate concentration of magnetic ions, Ov concentration sufficient enough grain size are greatly conducive to the formation of ferromagnetic order.[27] Fengchun Hu prepared Zn0.96Cu0.02Co0.02O nanocrystals by solid-state reaction method, the combination of x-ray absorption fine structure spectra reveals that the Cu and Co ions are substitutionally incorporated into the ZnO matrix and distribute randomly in the host.

Intraparticle diffusion model happened in rapid agitation intermittent reactor in the adsorption process often belonging to grain internal diffusion control process [9], the expression for: Qt= Kit1/ 2 (7) Where Ki (mg·g−1·min1/2), the rate parameter of stage i, is obtained from the slope of the straight line of qt versus t1/2.
Acknowledgments This work is supported by Liaoning provincial science and technology department, and the Fund item number is L2012144.

Obtained in high salinity brine oil and gas field, as the temperature increased from 25˚C to 85˚C, the corrosion rate of carbon steel at 70˚C maximum, with the increase of salinity, corrosion rate rise basically, but should also consider ion type and concentration; Na+, Ca2+, and Mg2+ in different forms in different corrosion process, Na+ and Cl-, inlaid in the corrosion product film NaCl crystal grain, and Ca2+ have a tendency to the participation of the biggest film, Mg2+ seldom directly involved in the corrosion process.
CRAs material tubing can meet the development requirements and reduce the corrosion failure risk, reduce the number of well repair.