Search results

Materials & Experimental Programme Three locations of Batu Pahat, Johor, Malaysia (as shown in Fig. 1(a)), which are slightly difference in terms of geography were chosen in this case study.
Aziz: American Journal of Applied Sciences, Vol. 4, No. 10 (2007), pp. 768-773
Ali: American J. of Engineering and Applied Sciences Vol. 1, No. 4 (2008), pp. 274-279
Ali: Journal of Applied Science, Vol.8, No. 21(2008), pp. 3986 – 3990
Islam: European Journal of Scientific Research, Vol. 22, No. 2 (2008), pp. 205-215

Mostafa School of Environment, Science and Engineering, Southern Cross University, Lismore NSW 2480, Australia.
Numerical approaches allow accurate modelling of the dynamic response of materials taking into account the elasto-plastic behaviour and damage modes [2].
Materials & Design. 2013;47:1-8
Journal of Materials Engineering and Performance. 2015; 24(1): 229-44
Journal of Applied Mechanics. 1963; 30(3):384-90

Key Engineering Materials. 496 (2011) 67-74
Journal of the Mechanical Behavior of Biomedical Materials. 10 (2012) 197–205 [10] A.D.
Inorganic Materials: Applied Research. 2- 3 (2011) 261-267 [12] G.S.Fox-Rabinovich, K.
Metal Science and Heat Treatment. 57: 9-10 (2016) 614-619 [20] A.
Filtered cathodic vacuum Arc deposition of nano-layered composite coatings for machining hard-to-cut materials.

Magnesium aluminate alkoxides were prepared by sol-gel with magnesium, aluminum and n-butyl alcohol as starting materials.
Experimental Mg, Al, n-butyl alcohol and catalyzer were used as starting materials.
References [1] Lepkova D, Baatarjav A and Pavlova L: Inter Ceram Vol. 2 (1993), p. 89 [2] Yiquan Wu, Yufeng Zhang: Materials Review Vol. 14(2000), p. 41.
Vilminot: Materials Research Bulletin Vol. 33(1998), p. 1717
Etienne, ect: Materials Research Bulletin Vol. 37(2002), p. 1041

Pruncu, Experimental assessment on machinability performance of CNT and DLC coated HSS tools for hard turning, Diamond and Related Materials, 119 (2021) 108568
Venkatesh, Multiobjective performance investigation of CNT coated HSS tool under the response surface methodology platform, Archives of Metallurgy and Materials, 66 (2021) 627-635
Alarifi, Machinability Performance Investigation of TiAlN-, DLC-, and CNT-Coated Tools during Turning of Difficult-to-Cut Materials, Journal of Nanomaterials, 2022 (2022)
Higginson, Elasto-hydrodynamic lubrication: International series in materials science and technology, Elsevier, 1977
Boness, Cage and roller slip in high-speed roller bearings, Journal of Mechanical Engineering Science 11 (1969) 181-188

And I adopt concrete damage model to define material properties.
Because masonry structure is a two-phase composite material that is built by brick and mortar two materials of distinct properties, in the process of the finite element modeling, simulation unit difficult, resulting in slow development of finite element analysis of masonry structures.
The mode of the finite element model of masonry structure The masonry structure is a two-phase composite material that is built by brick and mortar two materials of distinct properties, there are usually two types of models of its finite element analysis: a.Separate model.
Journal of Architecture and Structure Vol. 36-11 (2006), p. 77 [2] Zhou Yun, Zhang Wenfang and Zong Lan: Seismic Design of Civil Engineering (Science Publications, China 2011)
Journal of China Water Transport Vol. 9-1 (2009), p. 258.

The elasticity and rigidity of stuck materials should be ensured by the use of special techniques for stabilizing materials in the process of securing a three-dimensional form.
With that the indices of reinforced interlining materials on non-woven textile liner web are not inferior then indices of reinforced interlining materials on knitted textile liner web.
Offered spectrum of reinforced interlining materials is characterized in Table 4.
Development of reinforced interlining materials to regulate elastic properties / Indian Journal of Fibre & Textile Research.2017,42(2):150-159.
Development of reinforced composite materials with a nanoporous textile substrate and a brush-structured polymer interfacial layer / Russian Journal of General Chemistry. 2017, 87 (6): 1428-1438.

Experimental Materials and chemicals Nafion was purchased by Zeolyst international.
Vielstich,Methanol crossover effect on the cathode potential of a direct PEM fuel cell, Journal of Applied Electrochemistry, 35 (2005) 1239-1243
Argyropoulos,Performance of the direct methanol fuel cell with radiation-grafted polymer membranes, Journal of Membrane Science, 171 (2000) 119-130
Holmes,Nafion®/mordenite composite membranes for improved direct methanol fuel cell performance, Journal of Membrane Science, 369 (2011) 367-374
Jiang,Surface-modified Y zeolite-filled chitosan membrane for direct methanol fuel cell, Journal of Power Sources, 173 (2007) 842-852

Materials and methods Cheese making and HP treatment.
International Dairy Journal, 2008, 18(2):129-138
International dairy journal, 2004, 14(11):989-1001
Journal of dairy science, 2004, 87(10):3172-3182
Journal of food engineering, 2005, 69(3):269-274

Material Model In our basic model, the materials used are as follows: aluminum alloy 1100 beam and piezoelectric patch, made of the material PIC151 following the specification of PI Ceramic.
Journal Intelligent Material Systems and Structures, 5:12-20
Smart Materials and Structures, 11:527-533
Smart Materials and Structures, 16:1888-1897
Series: Materials Science and Engineering.