Search results

The Analysis of Metallic Materials Subjected To Cycles of Thermal and Mechanical Fatigue Dragoş Cristian ACHIŢEI1,3,a, Petrică VIZUREANU1,3,b, Mirabela Georgiana MINCIUNĂ1,3,c, Mohd Mustafa Al Bakri Abdullah2,3,d, Andrei Victor SANDU1,4,e 1Gheorghe Asachi Technical University of Iasi, Faculty of Materials Science and Engineering, Blvd.
Ghosn, Srramesh Kalluri, (Effect of surface impulsive thermal loads on fatigue behavior of constant volume propulsion engine combustor materials, Elsevier – Surface & coatings technology, (2004), 188-189 [11] Hornbogen E., Review Thermo-mechanical fatigue of shape memory alloys, Journal of Material Science, Vol. 39, (2004) 385-399
[13] Jun Li, Shengru Qiao, Dong Han, Mei Li, Damage behaviors of TiAl alloy under thermal fatigue and thermal cycling with dead-load, Materials Science and Engineering A 471, (2007) 106-112
[21] Cai B, Ma X, Moering J, Zhou H, Yang X, Zhu X, Materials Science and Engineering A, 626 (2015) 144-149
[22] Sun Y F, Xu N, Fujii H, Materials science and engineering A - structural materials properties microstructure and processing, 589 (2014) 228-234

Transformation efficiency analysis model of main raw materials The transformation efficiency analysis model of main raw materials is showed in Figure 1.
Journal of Zhejiang University (Science Edition), 2009, 36(1): 33-36.
Journal of Northeastern University(Natural Science), 2005, 26 (4): 363-366.
Materials and Design, 2010 (31): 2925-2931
Science press. 2004.

So under the same single pulse energy, the material with higher thermal conductivity and higher thermal diffusivity has a larger thermal effect volume than other materials.
Acknowledgements This project is supported by the foundation of Taiyuan science and technology bureau (070204023) References [1] K.H.
Pandey: Journal of Materials Processing Technology, vol. 149 (2004), p.272-277 [3] J.
Tsai: Journal of Materials Processing Technology, vol.87 (1-3) (1999), p. 139-145 [7] J.
Satyanarayana: Journal of Materials Processing Technology 153-154 (1-3) (2004), p. 978-981

It is a piece of work fused materials, aesthetics, computer and math.
Acknowledgements This work was financially supported by Science Foundation of Zhejiang Sci-Tech University（ZSTU1101804Y）, Key Laboratory of Advanced Textile Materials and Manufacturing Technology Ministry of Education (2011QN03), and QianJian Talent Fund (1107361E).
Textile Research Journal, 80/12(2010): p. 1191-1200
Textile Research Journal,. 79(18)(2009): p. 1715-1724
Advanced Materials Research Vols. 175-176 (2011): p.1035-1039.

In this paper, the impact pressure of abrasives acting on the polished materials was deduced by Field Theory and the model of surface roughness for polishing super hard materials with Abrasive Water Jet (AWJ) was established.
The theoretical model of surface roughness for polishing super hard materials with AWJ was finally built.
This project is supported by Key Project of Shandong Natural Science Foundation (Z2005F02) and J.
Ercan: Journal of Materials Processing Technology, Vol.147 (2004), pp.389
Chen: Chinese Journal of Nonferrous Metals, Vol.15 (2005) No.7, pp.1075.

(3) By assuming the materials of the FGM beam obeys Hooke’s law, it gives stress-displacement relations ,
Computational Materials Science, 44(2009): 1344-1350
Materials and Design. 31(2010): 3159-3166 [6] Y.
International Journal of Mechanical Science. 52(1010): 595-601
Computational Materials Science. 44(2008): 716-720

Different parameters of materials take on different performance of obstructing and suppressing gas explosion.
These materials are worth further researching.
[4] Jianliang Yu, Tao Cai, Yue Li: Journal of Combustion Science and Technology, Vol.14(2),2008 p.97-100
[5]Hefa Cheng, Xiaomei Huang, Guoxian Xue: Journal of Materials Science and Engineering,Vol.22(1) 2004:78-81
[7] Ying-an Kang, Jun-yan Zhang, Jia-cai Tan: Functional materials, Vol.2(37) ,2006, p.247-254

Materials and Method Materials Basic materials used in this study consist of laterite soil, fluvial sand and Portland cement type I.
Low cost of materials used approximately $23.18 USD/ton. 6.
Pengthamkeerati, Potential use of chemical sludge from water treatment system with cement in cement mortar and soil cement block, Rajabhat Journal of Science, Humanities & Social Sciences. 13(1), (2012), p. 48-54
Souza, The effect of incorporation of a Brazilian water treatment plant sludge on the properties of ceramic materials, Applied Clay Science, 53, (2011), p. 561–565
Chen, Waste Foundry Sand Reused as Clay Replacement for Tile Manufacture, International Journal of Transportation Science and Technology, Vol 3, Issue 4, (2014) , P. 339–351

The initial ratio of 87Sr/86Sr is the good “tracer” in study of diagenetic mineralization process and sources of ore-forming materials.
Ore-forming materials should come from the sedimentary strata, mainly fluid circulation and rock interaction, through the water/rock reaction, leaching solution formation, make the formation of the ore-forming materials into the solution.
Therefore, we concluded that the Ca source of ore-forming materials should be multisource.
The Ore-controlling factors and genesis of Huoshiya Barite-Fluorite ore deposit in Pengshui, Chongqing, Journal of Chengdu University of Technology(Science & Technology Edition).
Beijing:Science Press, p.157-196, 224-259, (1987).

Application of Automated complex Gas Reaction Controller for Hydrogen Storage Materials Investigation Viktor N.
Automated complex Gas Reaction Controller and its application for hydrogen storage materials investigation are described in this article.
Recently carbon materials, in particular, carbon nanotubes, have been regarded as reservoirs for hydrogen storage [2,3].
There is one main method of hydrogen storage materials investigation by automated complex Gas Reaction Controller – PCI curves fitting.
Pourpoint, Development of a Sievert apparatus for characterization of high pressure hydrogen sorption materials, International Journal of Hydrogen Energy. 35 (2010) 10387-10395