Search results

Thus, these tool materials are not suitable for machining titanium alloys.
Therefore, new cutting tool materials need to be introduced.
Xie: Materials Science and Engineering A, 190 (1-2) (1995), p. 173 [16] R.
Koksal, Journal of Materials Processing Technology, 99 (2000), p. 266 [38] L.
Grearson: Material Science and Technology, 2 (1986), p. 47

Long resistant with additives also increased which can be explained by the improvement of adhesion of bitumen with mineral materials of asphalt concrete.
Also studied the effect of additives on the adhesion of bitumen to stone material.
In general, long-term water resistance of asphalt concrete using additives increases that can be attributed to improved adhesion of bitumen with mineral composite materials.
In Transportation Research Record: Journal of the Transportation Research Board.
Journal of Association of Asphalt Paving Technologists, Vol. 74. 2005. p. 283-285.

Introduction Attenuating materials are usually produced by making semiconductor materials or easily polarized semiconductor materials disperse in dielectric substrate materials.
CNTs are newly developed nano-materials.
Materials Science and Engineering, Vol.
Microwave Journal.
Journal of Applied Physics, 2006, 99: 024308

Mathematical modeling of fire-proof efficiency of coatings based on silicate composition, Materials Science Forum, 1006 MSF, 70–75.
Materials Science Forum, 968 MSF, 361–367.
Materials Science Forum, 1006 MSF, 107–116.
Materials Science and Engineering, 527(26) (2010) 6980‒6986.
[19] Luca Gambirasio, EgidioRizzi,An enhanced Johnson–Cook strength model for splitting strain rate and temperature effects on lower yield stress and plastic flow,Computational Materials Science, 113 (2016) 231‒265.

The preparation of standard solution Standard stock solutions of Mn, Cu, Ba, Ni, Pb, Zn, Rb, V, Sr and Zr had purchased from the national standard material research center.
Acknowledgements This work was financially supported by the Shandong Natural Science Foundation (ZR2010DM002) and National Natural Science Foundation of China (41072138).
References [1] G Q Wang, X F Shi, Y G Liu, et al: Advances in Marine Science Vol. 25 (2007), p. 408-418 [2] J Chen, Z S An, H John: Quat Res Vol. 51 (1999), p. 215-219 [3] Sh H Wang, G D Zhang, J Sh Zhang, et al: Science and Technology Review Vol. 25 (2007), p. 22-27 [4] M J Wang, H B Zheng, X Xie, et al: Chinese Science Bulletin Vol. 56 (2011), p. 188-195 [5] J Chen, Y J Wang, J F Ji, et al : Quaternary Sciences (1999), p. 350-356 [6] Ch Zhu, Ch G Zheng, Ch M Ma, et al: Chinese Science Bulletin Vol. 50 (2005), p. 2240-2250 [7] J B Wang, L P Zhu: Journal of Lake Sciences Vol. 20 (2008), p. 715-722 [8] J Chen, H T Wang: Acta Geologica Sinica Vol. 70 (1996), p. 61-72 [9] M Zhao, X Ch Zha, Ch Ch Huang, et al: Journal of Soil and Water Conservation Vol. 26 (2012), p. 106-111 [10] R X Xin: Plasma Emission Spectrometry Analysis (Chemical Industry Press, Beijing 2004) [11] Y F Liu, J H Feng, Zh J Li, et al: Metallurgical Analysis Vol. 32 (2012), p. 52-54 [12] L Yang, M X Zhang, L
Zhao: Modern Scientific Instruments Vol. 1 (2011), p. 117-122 [13] Q C Xu, A D Sun, Y Q Shi: Guangdong Trace Elements Science vol. 17 (2010), p. 43-46 [14] H Liu, L Zh Xie, J Li: Chinese Journal of Spectroscopy Laboratory vol. 28 (2011), p. 179-182 [15] N Wang, J Y Zhao, X H Li, et al: Guangdong Trace Elements Science Vol. 18 (2011), p. 52-55 [16] Y M Sha, X P Zhao, G Zhang, et al: Rock and Mineral Analysis vol. 27 (2008), p. 291-294 [17] Y Xing, L Q Zhu, H Y Zhang: Journal of Anhui Agriculture Science Vol. 38 (2010), p. 15694-15695 [18] J Gu, J Zhou, J B Zhao: Bulletin of Soil and Water Conservation Vol. 3 (2010), p. 9-14

In this paper, we use reflective materials, LED lights and so on to enhance the security and functionality of suitcase by human factors engineering ideas.
By following human factors engineering thinking and multi-disciplinary knowledge, the reflective materials, LED lights and so on was used to enhance the design of suitcase.
High-tech security materials, reflective materials.
GUANGXI JOURNAL OF LIGHT INDUSTRY, 2008, 10 (10): 126-127
SCIENCE & TECHNOLOGY INFORMATION, 2005 (NO.24): 3-4.

Journal of Materials Engineering and Performance, 30, pp.5290-5296
Dental Materials Journal, 40(3), pp.743-749
Materials Science and Engineering: A, 685, pp.417-428
Materials, 17(3), p.712
Corrosion and Materials Degradation, 2(2), pp.190-209

The main advantage of this technology for material parts with small and complex shape is to manufacture cost-effective and high-volume products.
A short crack ,detect, can significantly decrease the tensile strength and fracture toughness of MIM materials[4,5].
Materials and Methods Three types of metal injection molding parts through two processes, with and without HIP, are investigated in this study (Table 1).
Lee, International Journal of Powder Metallurgy (1990)
S., et aI., Journal of Materials Science Letters(1987)

Liu: Journal of Materials Engineering and Performance Vol. 1 (1992), p. 183
Castro, M.F.de Campos: Journal of Magnetism and Magnetic Materials Vol. 328 (2013), p. 53
Journal Alloys and Compounds
Landgraf: Journal of Phase Equilibria Vol. 21 (2000), p. 443
Materials Science Forum Vols. 727-728 (2012), p. 169

Journal of Materials Processing Technology 1992,33(1): p. 195-214 [2] Obermeyer E J,Majlessi S A.
Journal of Materials Processing Technology.1998,75(4): p. 222-234 [3] Z Q Sheng,Jirathearanat S ,Altan T.
International Journal of Machine Tool and Manufacture .2004,44(5): p. 487-494 [4] Chengzhi S, Guanlong C, Zhongqin L.The International Journal of Advanced Manufacturing Technology 2005,26(2): p. 23-29 [5] Chengzhi Sun, Guanlong Chen, Qin Lin Zhong, Weigang Zhang.
Journal of Machine Design. 2 0 0 3, 20 (11) : p. 16-18.
Journal of Mechanical Strength,2001，23（1）：246-248.