Search results

Chemical Engineering Journal. 225: pp.109-119
Journal of Membrane Science. 325: pp.395-403
Chemical Engineering Journal. 199: pp. 138-139
Journal of Hazardous Materials. 176: pp.836–842
Reviews in Environmental Science and Bio/Technology. 10(2): pp.125-137

Introduction Initially, the deep-hole processing is only used in war industry, but with the development of science and technology, almost every manufacture department uses it.
Therefore, the resarch of ultrasonic vibration deep-hole honing technology play an important role in the difficult-to-cut materials deep-hole finishing process and ultra-finishing process.
Di: Journal of Materials Processing Technology, Vol.120 (2002), pp.101-106
Ma: Journal of Materials Processing Technology, Vol. 129 (2002), No.6, pp.207-211
Zhang: Journal of Zhejiang University (Engineering Science), Vol. 42 (2008) No.6, pp.1042-1045.

To blend polymers in either physical or chemical way , its performance can be improved,besides,the material and experiment cost can be reduced [3].
Experimental Materials Raw materials: Natural silkworm cocoon or silk.
Journal of Sericultural Science Vol. 31(3)(2005), p.306 - 310
[2] Xinsheng Zhu, Pang Juan, Zhenghua Zhou,et al.Journal of Synthetic Fiber Vol.(10)(2006),p.4-8
[4] Mashuhiro T,Giuliano F,John s.c.Journal of Polymer Science Part B:Polymer Physics Vol. 32(2)(1994),p.243-248.

Materials and methods Analysis of Essential Oil Healthy and mature aerial sections of D. stramonium were collected and divided into 1- 2 cm pieces.
The essential oils were obtained by means of steam distillation from air-dried materials.
It may be resulted from different materials, because mature aerial of D. stramonium were selected in our study, but fresh plants were used in their experiments.
Xu, Journal of Chemical Ecology (2002). 28: 1173-1182
Q Li, et al., Journal of Analytical Science (2007), 23: 697-700 (in Chinese).

The obtained simulation results are in good agreement with experimental studies The work was supported by grants of Ministry of Education and Science: project № 559.2014 References: [1].
Hight Walker, J. of Magnetism and Magnetic Materials, 31 (2007)p.311 [3].
,Effect of Mechanical Stress on Magnetic States and Hysteresis Characteristics of a Two-Phase Nanoparticles System, Journal of Nanomaterials, Vol. 2013, Article ID 687613, 15 pages [8].
Journal of materials science letters 17 (1998) 1949-1952 [11].
Cullity, Intro magnetic materials, Addison-Wesley Longman, 1972, p.666 [12].

The unburned brick was prepared by using the high titania blast furnace slag as an aggregate, styrene-acrylate emulsion as cementing materials and two admixtures.
In present paper, the brick sample has been prepared by using SAE as cementing materials instead of cement and fly ash and HTBFS as an aggregate [10-11].
Experimental Materials.
[2] Yatang Dai and Kefeng Tan: Journal of Southwest University of Science and Technology Vol. 18, No.3 (2003), p. 39-42 (In Chinese)
[10] Xiwen Sun, Jiantao Zhang, Zhiyuan Yang, Tiancai You and Yun Liu: New Building Materials Vol. 20, No.3 (2003), p. 5-7 (In Chinese)

Aluminium alloys are disposed with better mechanical attributes, higher resistance to corrosion and high temperatures opposite to conventional materials.
Bhagyashekar: submitted to Journal of Minerals & Materials Characterization & Engineering (2010) [3] S.
Nayak: submitted to ISRN Materials Science (2012) [4] A.
Farhangi: submitted to The Arabian Journal for Science and Engineering (2008) [5] P.
Vojtko : submitted to Materials Engineering (2008) [8] F.

To help protect the craft against attack with a machine gun and antitank, scientific institutions develop and test new energy-intensive materials and design armor. 1 2 3 2 4 2 Fig. 1.
In these small time steps, respectively, must reflect the entire history of the load, which directly involves the adoption of the relevant characteristics of the materials, that are dependent on the strain rate.
Bibliography [1] Barnat W., In polish: Wstęp do modelowania wybuchu podwodnego pod pojazdem gąsienicowym; „Introduction to modeling the underwater explosion under tracked vehicle”, Systems: Journal of transdisciplinary systems science, Oficyna Wydawnicza Politechniki Wrocławskiej 2012, Vol. 16, nr 3
[2] Szturomski B. with a team of contractors, In polish: Charakterystyki dynamiczne do symulacji numerycznej materiałów stosowanych na osłony antyterrorystyczne na jednostkach pływających, „Dynamic characteristics to the numerical simulation of materials used for anti-terrorist cover on watercrafts”; The report from research N508 - O/0054/32, AMW/MNiSW 2009; [3] MSC MARC – Documentation: Theory and user information.
H., A constitutive model and data for metals subjected to large strains, high strain rate, and temperatures, in: International Symposium on Ballistics, The Hague, The Netherlands, 1983, pp. 1–7; [9] Szturomski B., In polish: Inżynierskie zastosowanie MES w problemach mechaniki ciała stałego na przykładzie programu ABAQUS; „Engineering use of FEM in solid mechanics problems on the example of program ABAQUS”, Wydawnictwo Akademickie AMW - Gdynia 2013; [10] Flis L., Numerical Simulation Of Balistic Impact On 10GHMBA Steel Armor, Scientific Journal of Polish Naval Academy, ROK LI NR 1 (180) 2010, Wydawnictwo Akademickie AMW, Gdynia 2010; [11] Tugrul Özel and Yigit Karpat, Identification of Constitutive Material Model Parameters for High-Strain Rate Metal Cutting Conditions Using Evolutionary Computational Algorithms, Department of Industrial and Systems Engineering, Rutgers University, Piscataway, Copyright © Taylor & Francis Group, LLC, New Jersey, USA, Materials and Manufacturing Processes

Materials Sci. 52 (2012) 293–297
Materials Sci. 43 (2008) 171–178
Materials Sci. 50 (2011) 1326–1335
Materials Sci. 64 (2012) 209–211
Alexander, CRC materials science and engineering handbook, 3rd ed.

Department of Materials Science, Angstrom Laboratory, Uppsala University, Box 534, 751 21 Uppsala, Sweden 2.
Regarding the biocompatibility of such materials, much work has been done on the endodontic treatment material Proroot or MTA and on the Wollastonite materials [8].
In neutral pH, both materials seem stable, i.e. no dissolution of material.
Buggy: Journal of Materials Science: Materials in Medicine, 14 (2003) 923-938. 3.
Chamberland: Journal of Orthopaedic Research, 18 (2000) 140-148. 5.