Search results

El Mir, K.
Alaya, Effect of the annealing temperature on transparency and conductivity of ZnO:Al thin films, Thin Solid Films, 517 (2009) 6305–6309
Dinia, Effect of Al concentrations on the electrodeposition and properties of transparent Al-doped ZnO thin films, J.
Christian, Effect of different dopant elements ( Al , Mg and Ni ) on microstructural , optical and electrochemical properties of ZnO thin films deposited by spray pyrolysis ( SP ), Superlattices Microstruct., 52 (2012) 594–604

Furthermore, the milling speed used was in the low or moderate level and never exceeded 300/min for SiCp/Al composites.
Therefore, it is recommended that appropriate negative rake angle should be chosen when high speed milling SiCp/Al composites.
Cutting vibration was very severe due to the tool cutting the hard and brittle SiC reinforcement and the relative “soft” Al matrix and the very high cutting speed used.
Negative rake angle and relatively large tool nose radius were recommended when high speed milling SiCp/Al composites as far as cutting forces was concerned.
El-Gallab and M.

Schiller, et al., J Eur Ceram Soc. 21 (2001) 1693-1697
Uusim, et al., J Eur Ceram Soc. 20 (2000) 2331-2336
Jung, et al., J Kor Ceram Soc. 44 (2007) 451-456
Wang, J Mater Sci-Mater El, 23 (2012) 1775-1782
Hsi, et al., J Am Ceram Soc. 98 (2015) 1133-1136

Al-Issai, W.
Harel, A.L.
El-Gendy, W.S.
Abd-El-Haleem, Biosynthesis, characterization of some combined nanoparticles, and its biocide potency against a broad spectrum of pathogens, J.
El-Toni, H.S.

In this study, a monotonous mechanical test is performed on a sample in Al-alloy containing about twenty-five grains.
Si Fe Cu Mn Mg Cr Zn Al 0.45 0.45 0.10 0.10 2.2-2.8 0.15-0.35 0.10 Balance The specimen dimensions are 13x43 mm2 with a thickness of 0.5 mm (Fig. 2a).
Thus, for a sample in Al-alloy with a FCC structure, {111} and {200} plans are not considered.
References [1] Saai A., Physical model of the plasticity of a metal crystal CFC subjected to alternating loads: Contribution to the definition of multiscale modeling of shaping metal, Thesis (University of Savoie), (2008) [2] Saai A., Louche H., Tabourot L., Chang H.J., "Experimental and numerical study of the thermo-mechanical behavior of Al bi-crystal in tension using full field measurements and micromechanical modeling", Mechanics of Materials, 42 (2010) pp. 275-292
El Bartali, V.

Al Mn Si Fe Cu Ni Mg 5.60-6.40 0.26-0.50 <0.05 <0.004 <0.008 <0.001 Balance The structural observations were carried out on the obtained rods with a diameter of 6 mm using light microscopy (LM) and scanning and transmission electron microscopy (SEM, TEM).
STEM micrograph of RS material extruded at 623 K with element mapping (O, Al, Mg) of magnified area.
RS 623K RS 663K Cast 623K YS [MPa] 300 235 207 UTS [MPa] 370 298 302 El [%] 12.3 10.7 11.5 HV0.1 95.0 70.0 71.3 HV Std.
(b) Average values of mechanical properties: yield strength (YS), ultimate tensile strength (UTS), total elongation (El) and micro-hardness of as-extruded rods.

El Seould, A Koschella, LC Fidale, S Dom, T Heinze, Applications of ionic liquids in carbohydrate chemistry, Biomacromolecules. 8 (2007) 2629–2647
Mututuvari, A.L.
El-Zahab, C.D.
I. van Staden, et al., Investigations on hydroxyapatite powder obtained by wet precipitation, Advanced Topics In Optoelectronics, Microelectronics, And Nanotechnologies V, Book Series: Proceedings of SPIE-The International Society for Optical Engineering, 7821 (2010) 78210B 1-6

For instance Dobrazanski et al [6] managed to predict the mechanical properties of quenched and tempered steels using a neural network.
In another study, Bahrami et al.[7] investigated the effects of pre-strain, deformation temperature, morphology, and volume fraction of Marrensite on the mechanical properties of dual-phase steels at room temperature.
El-Sesy, Z.m.El-Baradie, Influence carbon and/or carbide on the structure and properties of dual-phase steels, Mater.

Womack et al, "after the equipment running smoothly, they are asked periodically time for the team collectively suggests ways to improve the process."
According to Womack et al; Toyota encourages its first level suppliers to talk to them about how to improve the design process.
Estorilio: El trabajo de ingenieros en situaciones de desarrollo de productos: Un trabajo de procesos basado en ergonomía (PhD Thesis, Escuela Politécnica Universidad de Sao Paulo 2003)
El-Haik: Desig for Six Sigma: A Roadmap for Product Development, London, McGraw-Hill, (2003)

Rayan3,4c 1Physics Department, Faculty of Science, Ain Shams University, Cairo, Egypt 2Physics Department, Faculty of Science, Al-QudsOpen University, Jenin, Palestine 3Central Metallurgical Research & Development Institute, P.O.
An investigation of electrical properties of porous silicon for different current densities was made by Algun et al.[3] and had concluded that both pore radius and concentration would grow when current density is increased.
El-Nahass, S.Y.
El-Zaiat, M.A.