Search results

Then the load was removed with all the data cleared, then the axial load was applied gradually until specified design value was reached.
On failure, there was a marked reduction in their horizontal resistances, plastic hinge was formed at near the bottom of a specimen, for there were a number of conspicuous large horizontal cracks near the peripheral ties, large amount of was concrete crushed and fallen off, with local protrusion of peripheral ties and buckling of longitudinal rebars, even longitudinal splitting at the corners of some specimens.Generally speaking, for LC-1~LC-3 cracked slightly earlier than LC-4~LC-6, while the cracks of LC-2、LC-4 developed most rapidly.

This data is used to calculate the reflected shock temperature using 1D normal shock relations [17].
So the reaction can be written as 2Ce0.5Cr0.5O2+δ → CeCrO3 + (0.5 + δ)O2 Thus Formation CeCrO3 occurs via reduction or oxygen evolution from fluorite lattice under shock dynamic loading in presence of Ar gas.

Experimental window and sample nomenclature A: Injection speed 1 [%] B: Injection speed 2 [%] C: Cooling time [s] D: Moving side temperature [oC] E: Fix side temperature [oC] F: Melt temperature [oC] 5-10 20-50 2-6 104-166 160-192 637-650 Measured data nomenclature Measured direction Type of roughness measure Sample surface X Parallel to flow direction Ra Rq Rt Cold Surface facing moving side Y Perpendicular to flow direction Hot Surface facing fix side Example: XRaCold Ra-value measured along the flow direction on the sample surface facing the moving side Table 2.
This is further supported by a strong significance of the interaction between C: Cooling time and E: Fix side temperature and the reduction of the roughness with increase cooling time for the surface facing the hotter fixed side.

Statistical analysis: The data was analyzed using one-way ANOVA followed by LSD method.
Consistent effects of inoculants containing bacteriostat at appropriate concentration on inoculation was that more nodules were produced, more nodule fresh weight and plant biomass have been reported earlier [13] and may attribute to the reduction of populations of ineffective native Rhizobium strains.

When the pH was greater than 6, the phosphate removal rate was almost no difference but it became a significant reduction at the pH >8.0.
Tab.1 The data sheet of the precipitate surface composition analysis after the reaction Element Wt% At% [Fe3+]/[OH-] 1:0 PK 5.84 6.04 FeK 39.50 22.68 1:1 PK 2.90 3.58 FeK 53.94 36.86 1:2 PK 2.47 2.93 FeK 38.53 25.38 1:3 PK 1.93 2.57 FeK 47.91 35.27 As shown in Tab.1, phosphorus element did exist on the surface of sediment after the reaction, meaning that phosphorus was adsorbed and removed by ferric hydroxide.

The first part of our argument will be to expose the economist’s arguments and then to look through the empirical data if the theoretical proposal is actually perceived by the entrepreneurs.
Actually, in this case, we observed at the same time a converging movement towards the reduction of different systems within a dozen years from the years 1990 and the creation of a new standard as a repost towards the dominant.

The membrane module was pre-pressured at 0.1MPa for 20min, until the water flux was basically stable, and the data were recorded.
For PVDF and PU, with PVDF content reduction and the increase of PU content, the coagulation value increased, which suggested that the phase separation was transformed from the solid-liquid demixing to the liquid-liquid deminxing for PVDF/PU blend casting solution.

Data indicates that 20% NaCl and aluminum hydroxide complexes can slow down pore pressure transmission.
The reduction in formation pressure is due to the higher membrane efficiency of such drilling fluid than that of conventional WBM system.

Effect of increasing SF levels on reduction of CH content.
From the same data, cumulative heat developed in the control Portland cement paste and the pastes with six levels of silica fume as cement replacement at the temperatures of was plotted and shown in Fig. 11.

A reduction in mineralization efficiency was observed at catalyst overdose due to light scattering by the excess catalysts and reduced the light penetration.
The photocatalytic data was also corroborated with the PL tests shown in the Fig. 2.