Search results

The Probability Distribution Modeling of Surface Heat Flux Density on Metal Material Chengzhi Yang 1, a, Li Zhou 2,b 1 Faculty of Information Engineering and Automation, Kunming University of Science and Technology, Kunming, China 2 Huaneng Renewables Corporation Limited, Beijing, China a yangchengzhi_614@yahoo.com.cn, b 1183589197@qq.com Keywords: Surface heat flux density; Probability distribution; Metal material; Energy saving Abstract.
Introduction Based on thermodynamic relations between the heating temperature of metal material and its heat flux density, the 3D surface heat flux density model of metal material is raised.
This model can reflect real surface heat flux density change of metal material.
Obviously the principle can extend and apply to all process of heating metal material.
Journal of Engineering for Thermal Energy and Power, 2006, 21 (1): 35-38

Material and Method Three types of zeolite materials code names (Z-01, Z-02 and Z-05) are investigated.
Table 3: BET analysis summary of Zeolite materials.
Fig. 3 shows the cumulated pore volume of the selected adsorbent materials.
Osinga, Thet-curve of multimolecular N2-adsorption, Journal of Colloid and Interface Science, 21(4) (1966) 405-414
Adsorbents and catalysts, Journal of Membrane Science, 96(1–2) (1994) 59-89.

The electricity materials play important roles in the study and some study will be put on it.
During the location process, engineering materials cost should be taken into consideration in order to get the cost minimum and efficiency maximum.
The transmission line materials cost of different voltage levels will be taken into account when selecting.
(5) Calculate the means of all the objects materials costs as the new centre of the cluster for each cluster
Chinese Journal of Hospital Statistics, Vol, 15(2008), p.9-12

Journal of Materials Science, 2016. 51(14): p. 6735-6749
Journal of Materials Science, 1991. 26(3): p. 588-592
Journal of Materials Science Letters, 1982. 1(5): p. 211-213
Journal of Materials Science, 2012. 47(1): p. 55-67
Journal of Materials Science, 1975. 10(10): p. 1802-1825.

Development of Flexible Tooling for Deformation Sensing Applied to Composite Materials Fabrication Process Ariana F.
Among the existing techniques for composite materials manufacturing, Vacuum Assisted Resin Infusion (VARI) is a liquid composite molding (LCM) process where resin flows through a dry fiber preform to fully impregnate it.
Vilà, Fabric compaction and infiltration during vacuum-assisted resin infusion with and without distribution medium, Journal of Composite Materials (2016) 687-703
Liu, Visualization of resin impregnation through opaque reinforcement textiles during the vacuum-assisted resin transfer molding process using ultrasound, Journal of Composite Materials (2014) 1113-1120
Hill, Fiber Bragg Grating Technology Fundamentals and Overview, JOURNAL OF LIGHTWAVE TECHNOLOGY (1994) 1263-1276

Therefore, EDM is an attractive technology for machining various types of materials [5,6,7].
Asibu, Principles of laser materials processing, John Wiley & Sons, New Jersey, 2009
Subramaniam, Experimental investigation on machining characteristic of Al 6061 hybrid metal matrix composite processed by electrical discharge machining, International Journal of Engineering, Science and Technology 3 (2012) 87-101
Liu, Effect of electrical discharge machining on the characteristic of carbon fiber reinforced carbon composites, Material Science. 6 (2001) 2037-2043
Amri, The Effect of EDM Die-sinking Parameters on Non-conductive Materials, Advanced Materials Research. 903 (2014) 56-60

Application of recyclable materials for an increase in building safety against the explosion of an improvised explosive device Lucia Figuli1, a, Martin Magura2,b ,Vladimir Kavicky1,c and Štefan Jangl1,d 1 Department of Technical Sciences and informatics, Faculty of Special Engineering, University of Žilina, Ul. 1.
In our research we have focused on recyclable materials that could provide such protection and their comparison with other known materials.
We present a FEM analysis of a wall strengthened with different type of materials.
In conclusion we show the economical and ecological comparison of used materials.
Using high pressure, the materials are mixed internally at a 1:1 ratio at the tip of the spray gun.

Furthermore, ceramic materials containing natural cracks were also evaluated by this technique.
From the results, it was shown that this technique is valuable as a novel NDE technique applicable to ferro-magnetic and para-magnetic materials containing fatigue cracks and to ceramic materials containing natural cracks.
Since high frequency current, which is not influenced by magnetic permeability, is impressed on the specimen, ferromagnetic materials as well as paramagnetic materials can be inspected.
Results and discussion Detection of artificial defects for conductive materials.
Li: Journal of Physics D Vol. 29 (1996), pp.233-239

Advances in Materials Science and Engineering, 2016, 1–9
Journal of Composites Science, 2(3),49
In Journal of Materials Processing Technology (Vols. 92–93, pp. 1–7).
ISRN Materials Science, 2012, 1–5
In World Academy of Science, Engineering and Technology, International Journal of Materials and Metallurgical Engineering (Vols. 8–8, Issue 3, pp. 221–221)

Gradient material design Ceramic/metal gradient materials are mixed in different proportions.
The ceramic/metal functional gradient thermal barrier coating materials is calculated by using particle swarm optimization algorithm.
Acknowledgment The paper is financially supported by China national natural science foundation (No.51139005),.
[5] Nie Ronghua, Jiao Guiqiong, Wang Bo,, C/, 2D braided SiC ceramic matrix composites, thermal conductivity prediction [J], composite materials, 2009, (13): 169-174
Ceramic Engineering and Science Proceedings, 2008, 15(4): 555-562.