Search results

Although the EIT has an inherent advantage of high speed data acquisition, the poor spatial resolution of the reconstructed image remains as challenging problem to be solved.
This results in reduction of the computational burden.

The SG can be used: 1) to generate electricity; 2) as city gas; 3) to produce direct reduction iron; 4) to produce chemical or energy product, such as carbinol and hydrogen.
Based on the data above, the autarky rate of electricity in each factory is obtained (table 4).

Poor surface quality can increase surface irregular roughness and cause reduced thermal and mechanical fatigue life and reduction in impact strength, leading to premature die failure.
These data are all averages of three experimental specimens in order to eliminate the random measure errors.

Its main elements are: a two-rotor GTD-350gas turbine engine, H-564 single-stage reduction gearing and the energy receiver in the form of a HWZ-3 water brake Froude.
Element Analysed function of the object, M = f(nPT, nGG) Linear (without interaction) Linear (with interaction of the first order) Square (without interaction) Square (with interaction of the first order) 1 Rates of the regression bi Const. -1565 -1905 3873 3109 nGG (L) 41 46 -119 -110 nGG (Q) - - 1,15 1,17 nPT (L) -9,4 -5,24 -7,44 3,01 nPT (Q) - - -0,01 -0,012 nGG · nPT (L) - -0,06 - -0,15 2 Average mistake of the respect Sbi Const. 243 1790 400 176 nGG (L) 2,9 26 10 4 nGG (Q) - - 0,07 0,03 nPT (L) 1,7 22 3,83 1,96 nPT (Q) - - 0,02 0,008 nGG · nPT (L) - 0,31 - 0,02 3 Quotient t=bi/Sbi Const. -6,4 -1,06 10 18 nGG (L) 14 1,78 -12 -29 nGG (Q) - - 16 45 nPT (L) -5,6 -0,24 -1,94 1,53 nPT (Q) - - -0,53 -1,39 nGG · nPT (L) - -0,19 - -7,4 4 Sum of rests MS 4603 5094 166 21 5 rate of the determination R2 0,957 0,957 0,998 0,999 Assuming the above and the data contained in Table 2, it was found that the best function of the test object is a second degree polynomial (square) with the

It is usually found to be the cause of structural failures and performance reduction during flight.
Table 1 Aircraft wing data No.

This study considers the option of replacement of a part of traditional quartz sand with various low-rigid additives for the purpose of reduction of the gradient between concrete structure element rigidity values.
The reliability of calculation data was assessed by comparison with results of full-scale experiments.

Table 7 Working performance of concrete mixture Numbers Surveillance project Cement Decrement[%] Slump[mm] Extend degree[mm] Reversed slump time[s] Air content[%] C30-0 0 200 390 18 1.5 C30-1 8 210 450 15 2.4 C30-2 10 210 445 16 2.3 C40-0 0 195 390 20 1.0 C40-1 8 200 455 17 2.6 C40-2 10 205 450 16 2.4 Cement is the main cementitious material of concrete, the hydration process is accompanied by the formation and breakthrough of potential barriers, about 20% of the cement failes to fully hydrated, only Play a role of filling, the electronegativity of alcohol amines groups in concrete synergist can enhance electrostatic repulsion of particles surfaces, the cement slurry dispersion improves[7], making cement paste to set data package to improve.
(3) Due to the reduction of cement dosage, the compensation of early cement hydration products on concrete shrinkage weakens, which results in makes early shrinkage of chip concrete increasing, but by stimulating the activity of the mineral admixtures, concrete synergist can promote gelled material hydration and compensate parts of shrinkage, make concrete contraction narrow and tends to be stable

The multilayer structure enables the reduction of the CTE difference between each coating in each temperature range to approximately 2´10-6 K-1, which is beneficial for minimizing thermal stress during temperature cycles and improving the thermal cycle lifetime of TBC.
The data for CuCrZr obtained from literature[[] Torben Fiedler, Martin Bäker, Joachim Rösler.

Jorgensen et al. studied the reduction of the reaction temperature while metal ions were doped in VO2 thin films using RIBS method [1].
To optimize the deposition process for V2O5 thin films, an orthogonal array using experimental data was employed.

The average crystallite size, D can be determined based on XRD data by using Scherrer’s equation [19]: D=kλβcosθ (1) where λ is the wavelength of x-ray used = 1.54059 Å, k = 0.94 known as shape factor, B is the broadening of the diffraction line measured at the half of its maximum intensity in radians and θ is the angle of diffraction.
Kurozumi, Microwave Dielectric Loss Reduction by Vacuum Treatment for (Ni,Zn,Fe)3O4 Films Prepared by Ferrite Plating, Magnetics, IEEE Transactions on. 32 (1996) 4183-4185