Search results

Moreover, gap thermal resistance relevance in the global heat transfer turns out less significant as its thermal resistance decreases due to gap reduction.
The fuel temperature measurements provided indirect information of the gap conductance evolution, and the amount of gases released by means of the rod pressure data.

Then for minimally treated salak pondoh fruit which was given cellulose + ZnO (nano-sized) nanocomposite coating showed a lower rate of total acid reduction compared to control (without coating).
For further research, to get better and more valid data, this research do compare test with another treatment of the coating.

In traditional cement production, to reach clinkerization temperature of 1450 °C, the CO2 emission from the fuel accounts for 40% [1]. 2) Extending the service life of concrete structure with the possibility of changing steel reinforcement to aluminium, which has better anti-corrosion behaviour and is much more durable in environments with carbonation or chloride intrusion. 3) Achieving weight reduction of RC structure.
During the pull-out test, the traction force and the displacement was recorded, and the data is transferred to stress-slip relationship, which is shown in Figure 6 and the bond strength is concluded in Table 4.

Puspita3,c, Darminto1,d and Risdiana4,f 1Department of Physics, Faculty of Science and Data Analytics, Sepuluh Nopember Institute of Technology, Kampus ITS, Sukolilo, Surabaya 60111, Indonesia. 2Department of Biotechnology, Faculty of Graduate School, Padjajaran University, Jl.
Parman, “Effect of Soaking of NaCl Solution on Reduction of Calcium Oxalate and Size of Amylum on Purple Yam ( Dioscorea alata L .),” NICHE J.

When the shot number is fixed, the ablated ring area becomes smaller with the reduction of the laser power.
By curve fitting to the data, we derived two curve fitting functions, and (Eth, Dp2) can be obtained by solving the simultaneous equations.

This improvement will result in a reduction in the amount of polyester resin used and the associated amount of styrene used in construction.
This data was used in FE simulation of the whole tank which was loaded in two ways: with defined external and internal overpressure.

It is well known that alloys of Mg-Al-Ca systems may provide significant improvement in elevated temperature properties due to reduction of volume fraction of Mg17Al12 phase and the formation of Al-Ca and Mg-Ca intermetallic compounds [1-3].
The literature data and morphology of CaMgSn phase suggests that these precipitates form as a primary solidification phase [16].

Data processing.
But during the removal proteins process, most of the proteins are decomposed or removed, which leads to the reduction of antioxygenic property DPNR.

In the last step, in order to form the mechanical induced ε-martensite phase, a cold rolling of 10% reduction at R.T. was carried out.
Although the detailed data are not presented here, the amount of ε-martensite phase was increased by 600℃ 500℃ 700℃ 350 300 250 600 700 Vickers Hardness, Hv 200 550 650 Maximum width of wear groove (µm) Without Training (276) Without Training (659) 1 2 3 4 5 Number of Training Cycles 0 (a) (b) 600℃ 500℃ 700℃ 350 300 250 600 700 Vickers Hardness, Hv 200 550 650 Maximum width of wear groove (µm) Without Training (276) Without Training (659) 1 2 3 4 5 Number of Training Cycles 0 (a) (b) Fig. 5 (a) Hardness and (b) wear property of thermally trained FM samples. 1 2 3 4 5 Number of Training Cycles ×10-4 500℃ 600℃ 700℃ 0 6.5 5.5Internal Friction, Q-1 Without Training (4.2×10-4) 1 2 3 4 5 Number of Training Cycles ×10-4 500℃500℃ 600℃600℃ 700℃700℃ 0 6.5 5.5Internal Friction, Q-1 Without Training (4.2×10-4) Fig. 4 Internal friction, Q -1, in thermally trained FM samples.

The delamination causes large reduction of strength and stiffness of the CFRP laminates, and it brings deterioration of structural reliability of the CFRP structures.
The data-standardization method provided significant improvement of performance of estimations [7].