Search results

For the former, the CuK𝛼 monochromatic X-ray source with 𝜆 = 0.154 nm was used and data was collected for the 2𝜃 angle ranging from 3° to 110°, with a 0.02° 2θ step size.
Pescarmona, Cu/Cu x O and Pt nanoparticles supported on multi-walled carbon nanotubes as electrocatalysts for the reduction of nitrobenzene, Appl.

The decrease in degradation efficiency above this optimum concentration of dopant ion, is due to reduction in light passing through solution, increase in light scattering [26] and de-excitation of active molecules by collision [27, 28].
The XRD data have shown wurtzite-type polycrystalline of Fe-doped ZnO nanoparticles.

All data were recorded until a 4 mm displacement of the central brick was reached.
The reduction in compressive strength could be ascribed to different mechanisms, ranging from overpressures boosting cracks propagation, to chemical reactions with Si-O groups on the surface of pores as well as to sliding of crystals; - moisture presence worsens the shear behaviour of triplets, by reducing the peak load and favouring slipping of the contact surfaces.

Calculating Weibull parameters by grouping wind data every 1 m/s using the Weibull calculator.
Results The geological and geotechnical data at the design site are as follows: A.
Wind Loads Recapitulation of wind load data based on load scenarios acting on the foundation can be seen in Table 9.
Biswas, “Wind data analysis of Silchar (Assam, India) by Rayleigh’s and Weibull methods,” 2010
Adayat, “Determination of the Undrained Shear Strength of Sensitive Clay Using Some Laboratory Soil Data,” Redfame Publishing, vol. 8, 2021

The welding arc is an extremely dynamic and variable process, continuously affected by a number of physical and metallurgical disturbances [3] such as: - ionization process of gases and metal vapour; - deposition and transfer of melted weld metal and slag; - metallurgical reactions of reductions and refinement of weld metal in puddle.
Slania, Objective methods for assessing the performance of welding power sources via a computer recording device and data processing, a general discussion, Welding Institute Bulletin (1991), N. 2-3 (in Polish)

However, the decrease of flying height will cause the occurrence of intermittent contacts, which lead to slider wear, the loss of data and even catastrophic failure of hard disk drive.
More precise simulation of slider-disk interaction dynamics is required for the reduction in the slider-disk spacing.

Then, in the high temperature tube furnace, the synthesis was performed at 1300 oC for three hours with a weak reductive atmosphere of flowing 5%H2-95%N2 which ensured complete reduction of Eu3+ to Eu2+.
The 1800s data were recorded.

Therefore, Chen and Lee [11] developed an intelligent fuzzy weighted estimator with higher target tracking performance and better noise reduction effectiveness.
The input estimation method uses the recursive form to process data.

The data demonstrate that the residual carbon source (ethanol) could be used for denitrifying reaction of next cycle, but the relative denitrifying rate will was decreased with the ethanol solution reused times.
Thus, the reductions of nitrate and nitrite were limited due to insufficient carbon source at these days.

Zhao[4] experiments that adopted axial vibration, the normal grinding force can be reduced by 1/3 to 1/4, and the across axis direction leads to a significant reduction of grinding forces and an increase in material removal rate while maintaining a slightly increase in wheel wear and surface roughness.
Measure equipments includes: ONO SOKKI LV-1710 Laser Doppler Vibrometer systems to measure the tiny amplitude; KISTLER Type-9257B dynamometer; Mitutoyo SJ-301 Surface Roughness Measurement; Sartorius RC 210 D Data Weighing Systems measures the amount of removal material; JEOL JSM-5610LV SEM to observe surface formation.