Search results

Linear least squares regression was then applied to the absorbance data as expressed by equation 1.
Results Table 1 lists the B12 concentration versus time data for each dialyzer and concentration reached at equilibrium before and after antibody were added to the system.
Since the system had come into equilibrium before the anti-B12 antibodies were introduced, the Ksink term represents “restored” clearance due to an immediate reduction in the concentration of free or “unbound” B12.

(b) Geometric construction of joint compression brace member Tension brace member chord member chord member multiplanar KT-joint multiplanar KT-joint compression brace member Tension brace member tie bar (a) Inverted trapezia-shaped roof truss Fig.1 The spatial parallel overlapped K-joint with two chords and the spatial KT-IPOv joints Fig.2 Multiplanar unstiffened tubular KT-IPOv joints Brief Introduction of Experiment The test data as revise of the finite- element analytical model derives from the test report[1]on the capability of butt-welded joint the tubular full penetration of Suzhou International Convention & Exhibition Center.
In Figure 13, the variation range of the ζt corresponding to that of the Φ is 70 degrees to 120 degrees, namely, data points 0.02, 0.05, 0.14, 0.23, 0.31, 0.39 of ζt in the figure respectively correspond to Φ equaling to 70°, 80°, 90°, 100°, 110°, and 120°.
Shanghai: Research Institute of Structure Engineering and Disaster Reduction, Civil Engineering College, Tongji University, China, 2004

Despite a number of investigations of Al–Mg-, Al–Mn-, Al–Mg–Si- as well as Al–Sc–Zr-based alloys there are considerably less systematized data about the Al–Mg–Si–Cr–Mn–Sc–Zr alloys in the literature.
%Zr alloy was conventionally cast (AC alloy) and also further deformed by cold-rolling with a reduction of 68 % (CR alloy).
Derivative resistivity data compiled in the previous studies of the heat-treated AlMnScZr alloys during isochronal annealing [2] do not differ in the temperature position of the I-stage in Fig. 3.

The most important is an ease of the experimental procedures and its separation from the reaction mixture including the pollutant reduction.
Table 4 provides the coefficients of two variants of the second order model including the relative Mean Absolute Percentage Errors (MAPE) between estimated (Yquadratic) and experimental data ( Yt) for n fitted design points as followed: MAPE=100nt=1n Yt-YquadraticYt Table 3.
The previous experimental data are used to validate the models in forms of MAE.

This size reduction process aimed to expand the contact surface between OPEFB and active agent in pretreatment process.
Based on simulation performed by SuperPro Designer v9.5 using all technical data parameter mentioned in Methods, production of rhamnolipid using solvent extraction purification methods required more OPEFB feedstock to produce the targeted production capacity than using adsorption chromatography.
In this study, calculation of profitability performed by SuperPro Designer v9.5 using economic data which accordance to planned design process simulation.

It is clear from the CA data that using nanoclay led to enhance ng the surface hydrophobicity of PLA film to a value of 14.7°.
Data pertaining to CA marked that the irradiation of 40 kGy increased the CA value to become (θ=58.4°).
In another part it is ascribed to the number of crystallites in terms of reduction surfaces under the melting peaks and the narrowing crystalline size distribution.

The purpose was to test whether the data collected by strain gauges and displacement meters were accurate and effective, and to make the specimen in good contact with the loading device, and then entered the formal loading stage.
The data in the test process were collected automatically by the instrument.
According to code DL/T 5085-1999, the predicted ultimate bearing capacity of CFST with DCLs column can be expressed as follows: (15) (16) (17) Where ,is the area of steel and concrete; is the yield strength of steel; is the cylinder strength of the concrete; is bearing capacity reduction factor considering slenderness ratio; is hoop Coefficient of Concrete Filled Steel Tubular; is limit value of hoop coefficient relating to concrete strength grade.

The data of stability and flow was recorded for each of the specimens.
The test sequence comprised of 150 conditioning pulses followed by 5 data acquisition pulses.
Reduction of plastic deformation in heavy traffic intersections in urban areas.

The purpose of the notification, investigation and analysis of accidents and incidents is to adopt the necessary measures to prevent their repetition by obtaining objective data that allow the facts to be defined and the basic causes that originated them to be established.
Dive data: Depth/Time at the bottom/Decompression 11.
Operational control, establishing specific methodologies and programs for the reduction and control of risks derived from underwater activities.

Fig.4 Arrangement of DWVG on absorber plate in solar air dryer. 2.1 Experimental data reduction Different studied parameters such as wall temperature, inlet and outlet air temperature, thermal efficiency, and useful energy were conducted in this experiment as described in the following: The mass flow rate value is gained by: 𝑚̇ = 𝜌𝑎 .𝑉𝑚.
The collected data reveals that for certain DWVG parameter values, a similar trend in thermal efficiency variation is gotten with different hourly solar irradiance in December.