Search results

Results and Discussion Fig. 1 depicts the density data and Table 1 summarizes the porosity values of composites sintered at different temperatures.
A dramatic reduction in mechanical properties of the HZC10 composite (16,42 MPa; 39,66 HV) was observed because of the formation of CS glassy phase (Figure 13).

The effect of the constraint is a reduction of the densification rate of the film as can be seen in Fig. 6.
Inserting the material parameters determined from the simulation in Eq. 8 give an excellent agreement with the simulation data (dashed lines in Fig. 6).

The noise reduction capability of a material is defined as its sound transmission loss (TL) effectiveness.
Table 7 The given data for four factors, each with three levels.

In SMF-Chord, the node maintains the forwarding load regulatory adopt_num according to the load information and follows the “slow increase, fast reduction” principle.
SWAM: a family of access methods for similarity-search in peer-to-peer data networks.

Type II: newly emerging OTAs Vacation tour products nonstandard products, huge market space; in the exploratory and incubation stage Transaction volume Number of user visits Tuniu, Uzai, Lvmama Type III: online shopping platform providers Air ticket + hotel standardized products; take advantage of the huge user flow but with insufficient experience in tourism industry; in the exploratory and incubation stage Transaction volume Number of user visits Taobao-tourism channel Paipai-air ticket channel Type IV: telecom operators Air ticket + hotel standardized products; take advantage of the mature voice search mode but with insufficient experience in tourism industry; in the exploratory and incubation stage Revenue volume Best Tone 122580, 116114 Type V: tourism B2B and B2C exploring websites Vacation tour products nonstandard products; take advantage of B2B platform resources; in the exploratory and incubation stage Transaction volume Number of user visits 17U.cn HUBS1.net Data
However, after two to three years of development, all emerging websites expand their products in an all-around way to package tour, DIY tour, and customized tour, etc., resulting in the reduction of their product difference.

The specification of geopolymer material provides numerous advantages over other materials, which include: reproduction of elements in high definition and excellent surface finish from standard fiberglass molds; rapid and controllable curing, which allows increased productivity through reuse of molds; low shrinkage allowing the perfect fit between parts; high resistance to fire and heat; durability and significant reduction of greenhouse gas emissions in its production, which generate environmental benefits proportionately.
Table 1: Molar ratio of geopolymer RAW MATERIALS OXIDE MOLAR RATIO PRECURSOR METAKAOLIN SiO2:Al2O3 2 ACTIVATOR POTASSIUM SILICATE SiO2:K2O 3.26 WATER 50% SILICATE + POTASSIUM HIDROXIDE SiO2:K2O 1.65 H2O:K2O 11.3 WATER 45% GEOPOLYMER TYPE K-(PSS)* Si:Al=2 *POTASSIUM-(POLI-SIALATE SILOXO) SiO2:Al2O3 3.5 K2O:SiO2 0.27 K2O:Al2O3 0.94 H2O:Al2O3 9.7 To calculate the quantities of starting materials, in addition to the technical data of products manufactured, X-ray Fluorescence analysis was realized to quantify the oxides present in an amorphous state.

This is leading to reduction in soil fertility and causing environmental pollution.
For this a frame of geometry as in plan is studied, important input data, results of post processing report and design samples are tabulated below.

The recovery of BSA after presaturation and ultrafiltration was calculated based on the detection result of untreated BSA solution called the basic sample (10µg/mL expected). 2.4 Statistical analysis All data are expressed as mean ± SD.
Comparing the results of protocol 1 and 2, the A450nm of TES immersion was significantly decreased after rising by protocol 2 (see Tab.2), which means the notable reduction of residual BSA in TES.

Power analysis determined that a sample size of 8 was adequate to detect differences in osteointegration of 15% or greater among groups with a power greater than 80% and an alpha of 0.05, which was based on data from previous studies [30].
In notable contrast to biomimetic HA, exposure of plasma-sprayed HA to a-calf serum for 48 hours resulted in non-uniform dissolution and reduction of coating tensile and shear strength [24].

This plot illustrates that the systematic reduction of the building block size leads to an increase of the strength (following a Hall-Petch curve), until a maximum is reached.
The data is plotted against the simulation time, before the shock front impacts the back surface of specimen.