Search results

This article we using brass as separated magnetic materials, using the DT4 electrical pure iron as the upper and lower fixed plate, the active plate material, the coil using a 0.8mm acetal enamelled round copper wire(Its nature see Standard: GB6109.3-2008).
One part of the magnetic flux to separated magnetic material (Region 7) and forms a loop.
Acknowledgements This work was financially supported by the National Natural Science Foundation (50975098).
[2] M R Jolly，J W Bender and Carlson J D: submitted to Journal of Intelligent Material systems and Structures (1999)
[3] Hang zhu, Shijun liu and Youlin Zhang: submitted to Journal of Materials for Mechanical Engineering (2007, In Chinese)

The integration of WSFs into construction materials offers a viable solution to address the growing environmental challenges associated with discarded tires.
Introduction The integration of waste tires or their components into civil engineering materials is essential for fostering sustainable development.
Aiello, “Experimental Study on Bond Behavior in Fiber-Reinforced Concrete with Low Content of Recycled Steel Fiber,” Journal of Materials in Civil Engineering, vol. 28, no. 9, p. 04016068, 2016, doi: 10.1061/(asce)mt.1943-5533.0001534
Kedir, “Synthesis and characterization of pyrolised recycled steel fibers for use in reinforced concrete,” International Journal Of Engineering Sciences & Management Research, vol. 4(6), no.
Guo, “A review on the properties of concrete reinforced with recycled steel fiber from waste tires,” Reviews on Advanced Materials Science, vol. 61, no. 1, pp. 276–291, May 2022, doi: 10.1515/rams-2022-0029.

Freeze-drying yields products with high quality and little or no shrinkage, but it is more expensive than hot air drying [1, 2].Another alternative, and a cheaper one, for producing materials with quality similar to freeze-dried products is called “puffing”.
Materials and Methods Materials Fresh winter jujube was purchased from local market in Tianjin, China.
During drying experiments, both the mass and temperature of the materials were recorded every two minutes during explosion puffing drying.
Ratti: Journal of Food Engineering, Vol.49 (2001), p.311 [2] K.S.
Amer Essa: Journal of Food Engineering, Vol.78 (2007), p.456 [7] P.S.

Preface    Dear Distinguished Delegates and Guests,  The Organizing Committee warmly welcomes our distinguished delegates and guests to the 2014 4th International Conference on Mechanical Science and Engineering (ICMSE 2014) held on January 2-4, 2014, Sanya, China.  
ICMSE 2014 is sponsored by International Association of Management Science and Engineering Technology (IAMSET).
Thanks also go to Advanced Materials Research Journal, for its wonderful editor service to this proceeding.  
CAO Jianguo, University of Science and Technology Beijing, China Prof.
LIEW Kim Meow, City University of HongKong, HongKong       Sponsors International Association of Management Science and Engineering Technology (IAMSET), HongKong Zhengzhou University, China  

And with the development of new material and technology new tungsten electrode doped with other rare earth elements has been developed.
Therefore it is meaningful to study the performance of new material for high powered pulsed xenon lamp cathode. 2 Experiments arrangement 2.1 Material preparation and processing In this research the electrode bar is made of powder metallurgy method[3].
And the electrode material composition see the table 1.
Effects of Y2O3 and CeO2 on the processing of Rare-earth-tungsten Materials.Journal of Beijing Polytechnic University, 1999, 25(4): 94～97,113 [4] XU Xue-ji,ZHU Ding-chang, Physics in gas discharge, Publishing House of Fudan University,1996 [5] HOU Zeng-shou, LU Guang-xi.
Principle of Metallography, shanghai science and technology press ,1996

Introduction Zinc oxide is a promising candidate material in science applications such as gas sensor [1], LED [2], microelectronic device fabrication [3] etc.
Optical transmission studies indicate that the materials possess exceptional transmittance and their band gap changed with respect to the different composite materials.
[4] Linxing Shi, Xangyin Li, Journal of Luminescence.134 (2011) 834
Jang , Optical Materials. 29 (2007) 1549
Wee, Materials (2010)3, 3642-3653; doi: 10.3390/ma3063642

Two important maps one of material bearing capacity and other of substratum for accurate depiction on geotechnical data was prepared by integrating geostatistical concepts into GIS.
Before any land is developed, its material properties need to be determined through geotechnical and geological testing.
Abdessamad, Monitoring the urban expansion and densification of Casablanca city morocco on more than a century using Gis and remote sensing, European journal of scientific research, (2016)
In International Journal of Applied Earth Observation and Geoinformation (Vol. 118).
Environmental Earth Sciences, 81(7). https://doi.org/10.1007/s12665-022-10287-y [12] Azougay, A., Rezqi, H., & Oujidi, M.

The firmer material may be confined to the side wall of the midsole, or it may extend a few millimetres beneath the medial heel region.
Wedging the midsole in a frontal cross-section with a uniform density of material significantly influences eversion of the rearfoot.
Friedman: Journal of Biomechanics, Vol.42 (2009), p.1444
Salo: Medicine and Science in Sports and Exercise, Vol.40 (2008), p. 707
Jones: Journal of Sports Sciences, Vol.27 (2009), p.855

Numerical Simulation Study on Damage Mechanism of Throat Armor Xiumei Zhang 1,a, Di Cui 1, Huijun Jia 1, and He Liang 2,b 1 Langfang College of Vocation and Technology，Langfang, China； 2College of Material Science and Engineering, University of Science and Technology Beijing, Beijing， China a zhangxiumeiliang@163.com, b lianghe163@yeah.net Key words: numerical simulation, damage mechanism, throat armor Abstract.
References [1] S.R.Zhang:J Journal of Iron and Steel Research, International, Vol. 13(6) (2006), p.1 [2] L.Du, and P.Liu: J .
Journal of Materials Processing Technology, Vol. (4) (2009), p. 3752 [4] L.J.

With the intelligent control technology employed in manufacturing systems [2,3], aerospace [4], transportation [5], computer science [6], intelligent construction [7,8], etc, its excellent performance draws more and more attentions of the clerk in construction project management.
As the major factors, man, material, machine, method and environment (4M1E), affect the general construction quality of LCP, which not only show their relative stability, but also vary with the procedure of LCP constantly.
References [1] SHE Lizhong: Research on Quality Supervision of Clusters of Engineering Projects Based on Science of Complexity.
Journal of Chongqing Jianzhu University.
Journal of Materials Processing Technology.