Search results

The material model was approximately described by a bilinear stress-strain curve.
Acknowledgements The research reported was financially supported by the National Natural Science Foundation of China (51008055), the China Doctoral Science Foundation (20100471124), and the Heilongjiang Province Doctoral Science Foundation.
Journal of Constructional Steel Research.
Journal of Constructional Steel Research, Vol.19(1999), No.1. p.1-19
Journal of Xi’an Institute of Metallurgy and Construction Engineering, Vol. 20 (1986), No.3.p. 363-370.

Data Upload And Download System Lead-in Material upload upload module mainly realizes the video tape, CD and so on and linear / nonlinear medium from the network upload file [1].
Journal of Jilin University ( Engineering Science) 2011，5: 1475-1479
Journal of Jilin University ( Engineering Science) 2010，6：1644-1649
Computer engineering and Science.2009,(S1):163-167
Journal of Jilin University ( NATURAL SCIENCE EDITION) 2009，1: 75-81

In the open, symbiosis environment, main manufacturers and suppliers spontaneously carry out material, energy, information exchange under the domination of rational individual targets.
Journal of systems engineering,vol.20-1(2005),p.12-18
Management Science, vol.43(1997),p.546-558
European Journal of Operational research,vol.153(2004),p.445-456
Journal of industrial engineering and engineering management, vol. 15-2(2010),p.1-7

Piccioni, Seismic Response of a Historic Masonry Construction Isolated by Stable Unbonded Fiber-Reinforced Elastomeric Isolators (SU-FREI), Key Engineering Materials (2014)
Construction and Building Materials, 21(2007), 1311–1321
Diaferio, Dynamic analysis of a historical fortified tower, Key Engineering Materials (2014) [16] T.
Lourenço, Non-destructive tests for the structural assessment of a historical bridge over the Tua River, Key Engineering Materials 569-570 (2013) 390-397 [21] A.
Piccioni, Mechanical characterization of Apricena marble by ultrasonic immersion tests, Key Engineering Materials (2014)

Experimental Procedures Materials and feedstock preparation.
Acknowledgments The authors acknowledge financial support from the Natural Sciences and Engineering Research Council of Canada (NSERC) under grant no.
Martin, Effect of binder jetting microstructure variability on low cycle fatigue behavior of 316L, Materials Science and Engineering: A 839 (2022) 142820. https://doi.org/10.1016/j.msea.2022.142820
Vieira, Influence of metallic powder characteristics on extruded feedstock performance for indirect additive manufacturing, Materials 14 (2021). https://doi.org/10.3390/ma14237136
Pasebani, A review on binder jet additive manufacturing of 316L stainless steel, Journal of Manufacturing and Materials Processing 3 (2019) 8–12. https://doi.org/10.3390/jmmp3030082

The good news was that the medicine dregs were utilized as the main raw material for anaerobic digestion to solve the pollution of residues and sewages to the environment, which had the advantages of simple operation, significant effect of gas production and high utilization rate of raw materials.
Materials and experimental methods Substrate and inoculum.
The physical parameters of the experimental materials are shown in Table 1.
Table 1 The physical parameters of the experimental materials Project Moisture [%] TS [%] VS [%] MLSS [mg•L-1] Anaerobic sludge 80.84 19.16 54.98 86360 Midday tea dregs 74.28 25.72 55.86 —— Honeysuckle dregs 78.09 21.91 69.97 —— Experimental device and methods.
Fig.4 The cumulative volume of methane production for the mixed dregs of honeysuckle and midday tea The physical parameters of the experimental materials were summarized in Table 1.

Materials Research Bulletin, 2012, 47(2): 375-380
Journal of Materials Chemistry, 2000, 10(9): 2213-2218
Materials Science & Engineering A, 2014
Materials & design, 2013, 45(Mar.): 407-411
Materials & design, 2018 144(APR.): 290-303

When watering, the advice can automatically start the water supply system through the pipeline reach the water pipe, and spray atomized supplement the water to the material during fermentation.
Acknowledgements This work was financially supported by the Beijing Municipal Education Commission research bases - technological innovation platform - forestry waste recycling innovation platform construction team (PXM2013-014207-000049), National Science and Technology Support Program - Cycle Agricultural Science and Technology Engineering (2012BAD14B09).
Sun, Study on Coriolus versicolor Used in Swine Manure Compost, Journal of Microbiology, 27（4）:91-93(2007) [4] K.
Liu, Isolation of Thermophile Microorganism from Cow Dung and Effects on Cow Dung Composting，Journal of Anhui Agricultural Sciences， 38（35）：20057-20059，20071(2010) [19] L.
Wang, Study on the Influences of Strawberry Growth Treated by Different Microbe Organic Fertilizers, Chinese Agricultural Science Bulletin, 25（08）:196-198 (2009) [21] R.

Acknowledgements This study was financially supported by the Science Foundation of Beijing Jiaotong University under the contract No.
References [1] Ramadan, M.; Takita, M.; Nomura, H.; El-Bagoury, N., Semi-solid processing of ultrahigh-carbon steel castings, Materials Science & Engineering A (Structural Materials: Properties, Microstructure and Processing), 430(2006), n 1-2, 285-91
Semi-solid casting and forging of steel, Die Casting Engineer, v 49B (2006), n 6, 32-8, [3] Seo, P.K.; Kim, D.U.; Kang, C.G. , Effects of die shape and injection conditions proposed with numerical integration design on liquid segregation and mechanical properties in semi-solid die casting process, Journal of Materials Processing Technology, v 176(2006), n 1-3, 45-54
Numerical integration design process to development of suspension parts by semi-solid die casting process, Journal of Materials Processing Technology, 183 (2007), 18–32

From the forming effect, full bore, in final parts did not appear lack of material, such as folding defect.
Acknowledgements This work was supported by the High-end CNC Machine Tools and Basic Manufacturing Equipment Special Major Science and Technology Project (Grant No. 2011ZX04001-011) and Industry Project of Qiqihar City (Grant No.
References [1] Yu Kun, Li Wenxian, Wang Ri: Chinese journal of Nonferrous Metals, Vol. 13, No. 2 (2003), p. 277-288
[2] Zhang Xianhong, Cui Zhenshan, RuanXue: Journal of Shanghai jiaotong university, Vol. 37, No. 12 (2003), p. 1874-1877
Sakai: Materials Science Forum, Vol. 419-422 (2003), p. 509-514