Search results

It approves as an effective grinding tool for machining C/E composite materials.
Composite Materials Handbook, Ch. 7, McGraw-Hill, New York, (1984)
Journal of Materials Processing Technology, 153-154 (2004) p. 920-924
Electrical discharge machining of carbon fiber composite materials.
Journal of Materials Processing Technology, 52 (1995) p. 386-398

A new polyferric silicate chloride(PFSC) was prepared by using sodium silicate, ferric chloride as raw materials, at the same time, its coagulation performance and the influencing factors were observed.
Thus, considering material cost, energy cost, stability and coagulation efficiency, Fe/Si mole ratio of 1 was best.
Acknowledgments This research was financially supported by The National Major Project of Science & Technology Ministry of China（Grant No.Z2008ZX07421-002） References [1] Hasegawa T.
Journal of Tianjin University of Science＆Technology.
Environmental Science&Technology.

Chinese Academy of Sciences).
Journal of Electronic Materials, 2008, 37(11): 1691-1697
Enhancement of thermal interface materials with carbon nanotube arrays.
Science, 2013, 339(6119): 535-539
Advanced materials, 2006, 18(11): 1468-1470.

Experimental Materials.
Park: Journal of Materials Science Vol. 28 (1993), p. 2950
Ortiz: Microporous and Mesoporous Materials Vol. 111 ( 2008), p. 523
Kwiatkowski: Journal of Colloid and Interface Science Vol. 330 (2009), p. 266
Lee: Applied Surface Science Vol. 255 (2008), p. 2466

This is an indication of the high corrosion resistance of both materials.
Kwon, Materials Science and Engineering A 390 (2005) p. 171
Perez, Materials Characterization 35 (1995) p. 145
Moosavi, Dental Materials, (19) (2003) p.188
Carvalho, Journal of Materials Science: Materials in Medicine (6) (1995) p. 523

CFRPs with impact damage and a composite component with cracks were inspected with these two methods, the results show that ultrasound excited thermography method is suitable for composite evaluation. 1.Introduction Composite materials features low weight, high strength, corrosion resistance and other merits.
(kg/m3) is material density and c(J/kg·K) is specific heat.
Acknowledgements This work was financially supported by the National Natural Science Foundation of China (Grant No. 61079020).
Schroeder, T.Ahmed and B.Chuadhry et al:Non-destructive testing of structural composites and adhesively bonded composite joints: pulsed thermography,Composites Part A: Applied Science and Manufacturing, Vol.33(2002), p.1511-1517 [2] W.
Wong:Evaluation of defects in composite plates under convective environments using lock-in thermography,Measurement Science and Technology, Vol.12(2001), p.142 [3] N.P.

Research of Artificial sites green roof for energy-saving efficiency in Taiwan Taichung Chen Chiou-Chuan1a, Lee Soen-Han2b 1Assistant Professor, Chung Chou University of Science and Technology, Department of Landscape Architecture,No.6,Lane2,Sec.3,Shanjiao Rd.
Materials and Methods (1)Empirical location: Taichung (Taiwan), a residential area second floor roof of a building on the top floor. (2)Empirical facilities: September 2011 facility complete, monitoring from January 2012 to May 2012.
Extensive green roof of vegetation layer Schematic diagram (3) Planting material: a perennial evergreen plants, Alternanthera payonychioides St., Rhoeo spathacea (Sw.), Angelonia salicariifolia Humb. & Bonpl.
&Lee,S.H., Research of green roof and facade vegetation reduce the heat efficiency (I) Journal of Health and Care Science Vol.1 N0.2 p88-103., (2012),Taiwan(R.O.C
[7] Sendo, T., Kanechi, M., Uno, Y. and Noboru, I., 2010, “Evaluation of Growth and Green Coverage of Ten Ornamental Species for Planting as Urban Rooftop Greening”, Journal of the Japanese Society for Horticultural Science, 79 (1):69-76

Mechanism of Ultra-precision Machining In the process of lapping, the action effect of abrasives and the properties of lap work material are closely related.
In the process of polishing, the properties of polisher material and abrasive powder are the essential conditions to ensure the super-smooth surface.
Cai: Journal of Synthetic Crystals, Vol.28 (1999), pp.346-349
[2] Y.K.Yap, M.Yoshimura and Y.Mori,T,Sasaki: Journal of Synthetic Crystals, Vol.S1 (2000), p.11 [3] J.L.
De: Materials.Sci.Forum, Vol.471-472 (2004), pp.473-476

FLAC3D has suitable constitutive models for geotechnical material simulation, which provides ten basic constitutive models, such as empty model, elastic models and plastic model [4].
In fact, any kind of model may not consider all factors, at the same time, it is impossible that one model be appropriate for all types of soil and the loading, only when the choice of constitutive model comply with the mechanical properties of engineering materials, this choice is reasonable.
Advances in Science and Technology of Water Resources.
Journal of Xi’an University of Science and Technology.
Journal of Shandong University of Science and Technology.

Materials and Methods The laboratory materials.
Acknowledgments This work was supported by Natural Science Research Project of Anhui Provincial Education Department (KJ2012B186).
Journal of Huaihai Institute of Technology.
Journal of Fisheries of China.
Bejing, China Science Press (1990)