Search results

Sisson1, c, and Jianyu Liang1, 2, d 1 Department of Materials Science & Engineering, Worcester Polytechnic Institute Worcester, MA, 01609, United States 2 School of Life Science and Technology, Beijing University of Chemical Technology Beijing, 110029, China a yaoyu9115@gmail.com, b ycen@wpi.edu, c sisson@wpi.edu and d jianyul@wpi,edu Keywords: graphene, nanosheets, synthesize Abstract.
Wang, Journal of Power Sources, 196 (2011) 10258-10262
Nagase, The Journal of Physical Chemistry C, 114 (2009) 832-842
Tutuc, Science, 324 (2009) 1312-1314
Papp, Advanced Materials, 25 (2013) 3583-3587

But its high operating temperature causes some negative consequences such as materials selection, cell sealing and lifetime.
Experimental Raw materials of analytical reagents lanthanum trioxide(La2O3), praseodymium oxide(Pr6O11) and tetraethyl orthosilicate(TEOS) were used to prepare the La10-xPrxSi6O27 via a sol-gel process.
Tolchard: Journal of Solid State Electrochem 10 (2006) 562-568
Sakai: Journal of Power Sources 195 (2010) 4059-4064
Romas-Barrado: Journal of Power Sources 195 (2010) 2496-2506.

Experimental Details 2.1 Coating materials.
The powder chemical composition of the two coating materials is shown in Table 1.
The powder chemical composition of the coating materials [wt.%].
Martin, Cavitation erosion of materials, Int.
Series: Materials Science and Engineering, 118 (2016) 1-8

The length of main shaft is 2580mm, steel shaft diameter is 130mm, and the largest diameter is 151mm including rubber material.
As Fig.1 shows the surface of main shaft of paper advance mechanism is rubber material.
It is soft material and the beating of surface is very great and it is very difficult to measure using touch measurement equipment.
Acknowledgement This study was supported by Guangdong Province Science and technology project(2009B010900031) and major breakthroughs in key areas of Guangdong and Hong Kong (Foshan special project) (2009Z013).
Chinese Journal of Lasers, Vol.37(2010),pp.231-235 (in Chinese)

Collected from Tianjin Binhai New District, the mainly raw materials used in this study are the saline soil (≥ 65%) supplemented with calcareous materials.
Introduction Nowadays there is an increasing demand and trend of using greening building materials, which requires not only utilizing a large number of industrial solid wastes, but also extensively using other low-quality soil resources, such as mud, saline soil and sandy soil, to produce new construction materials.
In the present study, using coastal saline soil as main raw material supplemented by a small amount of calcareous material, the microstructural characteristics of activated saline soil was analyzed, and the hydration products and reaction mechanisms of autoclaved saline soil were determined by using XRD, DAT and other microstructural analytical methods. 2 Experimental Materials and Methods 2.1 Experimental materials The saline soil used in this study was collected from the seaside coast stretching over 10 meters in Tianjin Binhai new district.
Saline soil, CaO, finely grinded quartz, natural sand and water were used as raw materials, in which the CaO dosages are 5%, 10%, 15% and 20%, respectively.
Journal of Chongqing institute of construction engineering,Vol.3(1991), p.80-83 [2] Huang Shiyuan..

So it is widely applied in the surface modification of various materials [1,2].
Sun: Journal of Materials Science and Engineering, Vol. 23 (2005) NO.2, P.167 (In Chinese)
Xu: Materials Science and Engineering A, Vol. 402 (2005), P. 135
Gnanamoorthy: Materials Processing Technology, Vol. 171 (2006), p.61
Gilewicz: Journal of Achievements in Materials and Manufacturing Engineering, vol. 37/2 (2009) P.498

Large deformations, material incompressibility, heterogeneities of the material, unilateral contact with Coulomb friction law are taken into account.
However, the high non-linearities related to materials, geometry due to large deformations, coupled phenomena (contact with friction, thermal-mechanical coupling, wear) reduce the trust in extrapolation capabilities of these results at high speeds.
We assume that material properties do not vary with the temperature.
This is a mixed Lagrangian/Eulerian approach in which, for an observer in the reference frame, the tire is a fixed set while materials flow through the refined stationary mesh.
Araki, Thermal Engineering Analysis of Rubber Vulcanization and Tread Temperatures during Severe Sliding of a Tire, Tire Science and Technology, Vol. 27 (1), p. 22-47, (1999) [10] J.

Three-Dimensional Numerical Simulation of Metal Flow in the Initial Stage of a Twin-Roll Strip Casting Process Qinghua Zhang 1, a, Bo Wang 1, b, Weidong Zhang 2, Jieyu Zhang 2, Zhiyu Liu 1 1 Material and Metallurgical School, Inner Mongolia University of Science and Technology, Baotou, 014010, China 2 Shanghai Key Laboratory of Modern Metallurgy & Material Processing, Shanghai University, Shanghai, 200072, China a qinghuazhang@foxmail.com, b wangbo@imust.edu.cn Keywords: Twin-Roll Strip Casting; Melt Flow; Numerical Simulation; Volume of Fluid Abstract.
Acknowledgments The authors gratefully acknowledge the research funding from the Science Foundation of the Education Committee of Inner Mongolia (NJzy08073) and the Project for Innovation Fund of Inner Mongolia University of Science and Technology (No.2009NC006) for the support which has made this research possible.
This work was also supported by Open Project of Shanghai Key Laboratory of Modern Metallurgy and Materials Processing (SELF-2010-04).
Garcia: Journal of Materials Processing Technology.Vol.102 (2000), p. 33 [7] W.S.
Fang and S.L An: Journal of University of Science and Technology Beijing, Vol. 13 (2006), p. 393 [11] B.

Experimental Materials.
All of the materials were used with preliminary treatment to remove any additives and prevent interference from extraneous substances.
Zhang, in: Journal of Textile Research, in Chinese, vol.23, 2(2002), p.35 [3] P.
Huang, in: Journal of Textile Research, in Chinese, vol.28, 10 (2007), p.30 [6] J.
Wang, in: Progress in Textile Science &Technology, in Chinese, 3(2007), p.40

The specimen material is mold steel P20 (hardness HRC30), and the sample size is 160 mm × 100 mm × 60 mm.
Acknowledgment The authors would like to thank Science plan project of Shenzhen (SY200806300273A), team creativity project (CXTD1-007) and nature science (LG-08001) of institute of Information Technology, and nature science of Guangdong (9151802904000008) for their financial support.
Zhao: Journal of Materials Processing Technology, Vol.192 (2007), p.175 [2] L.
Kaldos: Journal of Materials Processing Technology, Vol. 61 (1996), p.219
Liu: Machining Science and Technology, Vol.5 (2001), p.171