Search results

β-TCP becomes an ideal material for implants due to its time-dependent properties which supplies temporary support for bone growth and is finally replaced by natural tissue [2].
Material and Methods Sample preparation β-tricalcium phosphate powder (β-Ca3(PO4)2, purity 96%, Sigma-Aldrich) was used as the raw material in this work.
Journal of the mechanical behavior of biomedical materials, 2016. 53: p. 434-444
Materials Science and Engineering 2009; 29: 1144-49
The Properties of Sintered Calcium Phosphate with [Ca]/[P] = 1.50 International Journal of Molecular Sciences 2012; 13:13569-86

Several in-situ techniques are being investigated to get improved quality composite materials.
Schematic of in-situ stir casting process for the synthesis of Al-matrix composite materials.
The efficiency of salt route technique is quite good in synthesizing ceramic reinforced Al-composite materials.
Liu, Effects of copper addition on the in-situ synthesis of SiC particles in Al-Si-C-Cu system, Materials and Design, 63 (2014) 194-199
Ermoshkin, Role of halide salts Na3AlF6 and Na2TiF6 in SHS of Al-10%TiC nanocomposite alloy in Al-melt, Life Science Journal, 11 (2014) 570-575

(4) Material feature: It reflects the material status of mechanical parts and the related information of heat treatment, involving the material category, rolling condition, mechanical properties, chemical composition, microstructure, heat treatment and surface treatment, etc.
According to the rule-based reasoning of process planning, the mechanical evaluation criteria to the material will be deduced from the knowledge base
Fourthly, define material feature.
For example, the material of this pump body is HT150.
Journal of Computing and Information Science in Engineering，2010, 11(3):245~256

According to the request of National Nature Science Foundation, the new diffusion welding method is put forward, that is the liquid-phase-impacting (LPI) diffusion welding.
In this paper, the mechanism of LPI and microstructure of welded joint of aluminum matrix composite SiCp/101A have been studied by scanning electron microscopy (SEM) and TEM, etc. 2 Experimental material and process 2.1 Experimental Materials The 101 aluminum matrix composite reinforced with 20% volume fraction SiC ∗ Funded by The National Nature Science Foundation of China (No.50171025) particulate with mean size of 12µm, was made by stirring casting.
Key Engineering Materials. 1995, (1): 3-36 2.
Journal of Materials Science and Technology. 2003, 19 Suppl.1: 88-90 4.
Designing of Interfacial Structures in Advanced Materials and their Joints.

Materials and Methods PET films (purchased from 3M Company) of 7x7cm 2 in size were washed by acetone, chloroform, deionized and water respectively, and then dried at room temperature.
Our previous report [5] gave the formula of free energy of adhesion between materials and bacteria: ( ) ( ) ( ) ( ) ( ) [] +−−+ +++− −−−+ −−−+ +−+ +−−−−−=∆ BSBS LB SL LB SL LW L LW B LW L LW S LW B LW S AdhF γγγγγγγγγγγγ γγγγγγ 2 2 2 2 .
Table 1 Contact angle (in degrees) and surface energy components of bacteria cells and supporting materials (in mJ/m2) Conclusions The chains of chitosan were successfully grafted on the surface of PET by plasma inducing and ultraviolet radiation.
Frey: Journal of Applied Polymer Science, Vol. 81 (2001), p.2993-3001 2.
Lin: Materials Science and Engineering C 20 (2002), p.167-173 4.

Numerical simulations indicated that the compressive thermoelastic stress at the growth temperature is lower around the edges of material from which wafers would be sliced, as shown in Fig. 3.
Schroder, Progress in SiC Materials/Devices and their Competition, International Journal of High Speed Electronics and Systems 21 (2012) 1250009-1-24
Whiteley, Large Area 4H SiC Products for Power Electronic Devices, Materials Science Forum 858 (2016) 11-14
Hallin, High-Power SiC diodes: characteristics, reliability, and relation to material defects, Materials Science Forum 389-393 (2002) 1259-1264
Stach, Stacking fault formation via 2D nucleation in PVT grown 4H-SiC, Materials Science Forum 821-823 (2015) 85-89

Materials, 13(7):1549, 2020
International Journal on Advanced Science, Engineering and Information Technology, 6(4):534, 2016
Materials Science and Engineering: A, 773:138849, 2020
Materials, 16(3):1084, 2023
Materials Science and Technology, 33(2):138-148, 2016

Acknowledgements This work was financially supported by the National Natural Science Foundation of China (51178471), Natural Science Foundation of Guizhou Province of China(XJGC20130904).
Vibration Control of Cable-Stayed Bridges by MR Damper[M].Beijing: Science Press,(2007) [2]Wang Xiu-yong.
Journal of Engineering Mechanics Division, ASCE, 102(EM2), 1976, 102(2): 249-263 [6] Xiao Zhi-rong.
Applied Mechanics and Materials, Vols. 94-96, 2011, 9(02) :902-908 [9] Zhang Zheng-xin, Huang Fang-lin A New Magneticrheological Damper Nonlinear Bingham Hysteretic Model and ANSYS Implementation [J].
Applied Mechanics and Materials Vols .351-352 2013:1146-1151.

The material for nozzles is stainless steel.
Adler, The Mechanics of Liquid Impact, Treatise on Materials Science and Technology. 16 (1979) 127-183
Geskin, L.Tismeneskiy, Mathematical Modelling and Experimental Verification of Stationary Waterjet Cleaning Process, Journal of Manufacturing Science and Engineering. 120 (1998) 571-579
Balachandar, An Experimental and Numerical Study of Water Jet Cleaning Process, Journal of Materials Processing Tech. 211 (2011) 610-618
Ungureanu, Research about Automatic Adjustement Solution of the Advance Force at the Perffusion Drills Using Fluid Elements, Archives of Mining Sciences. 58 (2014) 1201-1208

The chemical compositions of the main materials used are presented in the Table 1.
Chemical composition used as filler natural materials, mass. %.
Most often, polyurethane foams are combustible materials of average flammability [8 ... 10].
Berlin, Combustion of polymers and polymeric materials, Sorov Educational Journal. 9 (1996) 57-63
Novikov, Polymeric materials for construction: Handbook, Higher School, Moscow, 1995