Search results

To observe contrast of influence of depth of cutting on force of cutting of three materials directly, the data was drew in the figure(shown in Fig.2).
To observe contrast of influence of depth of cutting on force of cutting of three materials directly, the data was drew in the figure(shown in Fig.3).
Hence, the contrast test of temperature of cutting of three materials was carried out to study the problem further.
Liu, Technology of highly efficient tool under the condition of extremely heavy load, Journal of Harbin University of Science and Technology, 16 (2011), 11-12.
[6] Y.N.Cheng, X.L.Liu, Z.J.Li, Adhering failure of the tool-chip in the process of extremely heavy cutting, Journal of Mechanical Engineering. 44 (2010), 67-69.

In the process of heap, the large granular materials will be crushed smaller with the gravity or man-made compaction, that is, granular material will occur the particle breakage phenomenon, which will make the grain composition change.
Experiment introduction The test materials were selected from dumping site of a opencast mine in Yunnan.
The results indicate that using fractal dimension to describe the breakage rate of granular materials is entirely feasible.
Acknowledgements This work was financially supported by Natural Science Foundation of Yunnan Province (2009ZC020M), Innovation Team Program of Kunming University of Science and Technology.
Journal of Southwest JiaoTong University,2002,37(2):186－189.

Fujita, "Fracture Toughness and Microfractures of a Sheet Molding Compound Composite", Journal of the Society of Materials Science, Japan, Vol.35, No.396, (1986), 1016-1022. 49.
Kamiya, "Fiber Bridging Effect on Opening-Mode Crack Extension Resistance of Unidirectional Fiber-Reinforced Composites", Journal of the Society of Materials Science, Japan, Vol.37, No.416, (1988), 505-510. 63.
Sekine, "Probabilistic Study of Debond Length and Pull-Out Length of Fibers in Unidirectional Fiber Reinforced Composites", Journal of the Society of Materials Science, Japan, Vol.38, No.425, (1989), 106-110. 65.
Sekine, "Micromechanics Study of Crack Propagation Rate in Glass Fiber Reinforced Plastics under Acid Environments", Journal of the Society of Materials Science, Japan, Vol.39, No.441, (1990), 737-741. 71.
Beaumont, "Micro-Mechanical Theory of Macroscopic Stress-Corrosion Cracking in Unidirectional GFRP", Journal of Materials Science, Vol.41, No.14, (2006), 4604-4610. 204.

Materials Science,2010,24(11):2-3
New Chemical Materials,2006, 34 (5): 115-127
New Chemical Materials,2009,37(5): 21-30
Rare Metal Materials and Engineering,2007,36(3): 17-19
Journal of Catalysis,2011,32: 555–565.

The work materials with initial diameter of 55mm and total length of 220 mm were chosen.
[2] A.Shokrani, V.Dhokia, S.T.Newman, “Environmentally conscious machining of difficultto- machine materials with regard to cutting fluids”, International Journal of Machine Tools & Manufacture, 57 (2012), p.83-101
A.K.Ghani, I.A.Choudhary, Husni, “Study of tool life, surface roughness and vibration in machining nodular cast iron with ceramic tool”, Journal of Materials Processing Technology, 127 (2002.), p.17-22
D.K.Sarma, U.S.Dixit, “A comparison of dry and air-cooled turning of grey cast iron with mixed oxide ceramic tool”, Journal of Materials Processing Technology, 190 (2007), p.160–172
Tugrul ozel, Yigit Karpat, Luis Figueira, J.Paulo Davim, Modelling of surface finish and tool flank wear in turning of AISI D2 steel with ceramic wiper inserts, Journal Of Materials Processing Technology, 189 (2007), p.192-198

This study provided the theoretical basis for cellulose acetate prepared by electrospinning in antimicrobial food packaging materials development.
Until now, many synthetic and natural biopolymers have been electrospun into ultra-thin fibers; however, electrospinning of functional packaging materials is still relatively small[2].
However, the studies of cellulose acetate in the field of packaging materials are still limited.
The technique allowed us to develop novel food packaging materials for the controlled release of the antimicrobial agent[6].
Experimental Materials.

[2] Tracy JJ, Pardoen GC: Journal of Composite Material.
[8] Camanho PP, Matthews FL: Journal of Composite Material.
[9] Chang FK, Chang KY: Journal of Composite Material.
Labeasb: Journal of Composites.
[11] Jian Tang, Zongjie Cao: China science and technology information.

Experimental procedures Materials and methods.
The bulk density and wear resistance of the Y2O3-added materials are improved largely than that of Y2O3-free materials.
Hence, it is evident that adding Y2O3 to alumina ceramic is a useful method to enhance the sinterability of materials.
Wang: Materials Transactions.
Sil: Indian Journal of Engineering & Materials Sciences r.

Experiment Materials and methods.
International Journal of Materials, Mechanics and Manufacturing 6 (2018) 142-146
Materials Science and Engineering: C 84 (2018) 67-79
Materials Science and Engineering: C 68 (2016) 198-204
Bioactive Materials 4 (2019) 8-16

The development of a new reinforcing material on carbon black-enhanced applications and traditional reinforcing materials.
The physics of rubber elasticity.for Composite Materials.
Journal of Engineering Science and Technology, 16(2) , pp.1601-1613
Journal of Engineering Science and Technology, 15(3),pp. 2051-2061
Journal of Engineering Science and Technology, 17(5), 3160-3173