Search results

CMR is assumed and based on the facts; 1.
Fig 1 shows the (CMR) philosophy.
b) Level 2; 1.Cutting speed, 2.
Fig 4: total machining time Summary 1.
International Journal Advance Manufacturing Technology 20:475–479

In order to improve the surface energy of PP, researchers have done their best in many modifications[1-6].
Standard curve was decided by a series of cardanol standard solution at 273 nm and 90 °C after dissolved in 1-octane.
Scheme 1 Chemical structure of cardanol Results and Discussion Effect of Initiator on Grafting Ratio The effect of initiator type on grafting ratio was investigated in order to select the optimum initiator (Table 1).
References [1] H.
New York: Hanser, 1985: 479-509.

This system is a closed hydraulic loop system, as shown in Figure 1.
This article using hydrodynamic cavitation generator perforated plate, as shown in Figure 2, the geometric parameters are shown in Table 1.
References [1] Botha,C.J, A study on hydrodynamic cavitation as a method of water treatment.
Divisions of Chemical Engineering, 2001,17(1):1-85
[7] Chen Lijun,Wu Chunde,Zhang Jiexin, Hydraulic cavitation applications in water treatment research progress [J].Ecological science,2006,25(5):476-479.

First steps on the modeling and simulation of thermoplastic / thermoset phase separation Hajer Lamari1, Amine Ammar2, Adrien Leygue1 and Francisco Chinesta1 1 EADS Corporate Foundation Chair, GeM UMR CNRS – Ecole Centrale de Nantes 1 rue de la Noe, BP 92101, F-44321 Nantes cedex 3, France 2 Arts et Métiers ParisTech 2 Boulevard du Ronceray, BP 93525, F-49035 Angers cedex 1, France 1{Hajer.Lamari, Adrien.Leygue, Francisco.Chinesta}@ec-nantes.fr 2 Amine.AMMAR@ensam.eu Keywords: Phase separation, polymer mixture, spinodal decomposition, Cahn-Hilliard, FENE viscoelastic model Abstract: Matrices employed in composites parts of aeronautic structures consist of a thermoset / thermoplastic mixture.
The model parameters were set to: ηs = 0.1, χ = 2.5 and κ = (1/60²).
References [1] A.
Phys., 49, 435-479, 1977
Phys., 42/1, 93-99, 1965 [5] H.

Then, the oven temperature was programmed from 40 to 200 ºC (held for 1 min) at 10 ºC/min.
Figure 1 Schematic diagram of the flow detection system of QCM Figure 1 illustrate the schematic diagram of the flow detection system of QCM.
Table 1 showed the results.
References [1] C.
J., 2004, 4(4), 479~488

The length of the straight section① is Lc ,the curvature radius of ② and ④is R, the corner is β, the length of straight section ③ is L, the total length of the fiber is Lf, the specific values is showed ​​in Tab.1.
Table.1 The specific size of the selected hooked-end steel fibers parameters r Lc R L Β Lf values 0.45mm 1.83mm 2.23mm 1.36mm 0.66 60mm The elastic modulus of the steel fiber is 2.0 × 105MPa, Poisson's ratio is 0.3, tensile strength, 1450MPa，steel fiber is considered ideal plastic.
In order to meet the requirements of the model , the sharp of the section should be changed to the rectangular by equivalent change in area and moment of inertia of area, the length and width of a rectangular cross section to meet the requirements can be obtained by following two equations : ( 1 ) ( 2 ) Fig.1 The shape and size of hooked-end steel fibers Fig. 2 Mesh for the pull-out model of hooked-end steel fiber The ratio of the rectangular cross-section can be calculated by Formula(1) and (2).
Table.2 Two peak loads and the corresponding pull-out displacement load diaplacement The first peak load 479.9N 1.440mm The secondpeak load 314.9N 4.628mm It is showed by Fig.3 that the pull-out process of hooked- end fiber can be divided into the following phases: (1) before the end of the fiber is pulled , the relationship of load and displacement is linear , with the increase of load, the end of the fiber is pulled out, the nonlinear relationship between load and displacement occur, the first peak load appear when the pull-out displacement δ= 0.144mm, yet the end of the fiber of hook is near but do not pass the first corner, (2) after the peak , the end of the fiber begin to pass the first corner and the load began to decline, (3) When the displacement δ= 3.816mm, end of fiber entirely pass the first turn into the straight section ③ and the load began to rise with increase of displacement ,(4) When the displacement δ= 4.628mm, the end of fiber has not yet reached the second
References [1] H.T.

Hydraulic results were shown in Table 1.
Table 1 Sand types and hydraulic conductivities of the plates Plate No.
Effluent was sampled every 1-2 minutes at the outlet using a 10ml vial.
References [1] A.
Tsang, Channel Model of Flow through Fractured Media, Water Resources Research. 23(3) 467-479, 1987

Table 1 summerizs the values of Tg, Tx, and ∆Tx for all the samples investigated in the present study.
plots, ln(Φ/Tx2) versus 1/Tx, of the amorphous Ti50Cu28Ni15Sn7 and that with 4 vol.% SiC.
Fig.1 X-ray diffraction patterns for mechanically alloyed Ti50Cu28Ni15Sn7 and composite powders after 8h milling.
References [1] A.Inoue: Mater Sci Forum Vol. 312-314 (1999), p.307
Lee: Mater Sci Forum Vol. 475-479 (2005), p.3443

Experimental The chemical composition of 40CrNiMo7 steel is given in Table 1.
The schematic diagram of HCPEB source is given in Fig.1.
Fig. 1 Schematic diagram of HCPEB source
References [1] T.
Forum Vol.475–479 (2005), p. 3673 [6] Shengzhi Hao, Bo Gao, Aimin Wu, Jianxin Zou, Ying Qin, Chuang Dong, Jian An and Qingfeng Guan: Nucl.

Applications of RiverCAT in the field measurement of reservoirs JING Hefang1, a and LI Yitian2,b 1 Res.
Figure 1.
References [1] T.A.
Journal of Hydrology, 2013, 479:180–188 [3] M.L.
Journal of Hydraulic Engineering (ASCE), 2004,130, 9(1): 932-936