Search results

The instruments and materials used in the experiment were multipoint temperature collecting instrument (FLUKE-netDAQ32), thermostatic oil bath (CH1506), computer, thermocouple, iron wire, an aluminous can of which size was similar to simulation, bracket, rubberized fabric and plastic tube.
Journal of Food Engineering, 2002, 51 (3): 221~228
Journal of Food Engineering, 2002, 51 (1): 77~83
Journal of Food Engineering, 2001, 48 (2): 147~156
Journal of Food Engineering, 2007, 80 (4): 1031~1042

With the development of materials science and interdisciplinary convergence of disciplines, multi-doped gradually replaced single-doped as the mainstream doping mode due to its application diversity and abundant property of aggregation of each materials [10-12].
But, there is no report on the Co-Ga co-doped in chalcogenid materials.
Journal of Materials Science vol.53 (2018), p.1286-1296
Materials Letters, Vol.66 (2012), p.121-124 [18] M.
Materials Chemistry and Physics Vol.133, p.823-828 [19] X.C.

According to Bignozzia [10], sustainable building materials are usually based on recycling of proper waste that, thank to its own characteristics, can partially and/or entirely replace natural materials deriving from no-renewable resources.
Mixture name of the different composite materials were : P0 (without plastic waste), P6, P12 and P17.
Houivet: submitted and accepted to Environmental Engineering and Management Journal (EEMJ), (2013).
Senhadji, in: Proceedings of 2nd International Conference on Advances in Materials Science and Engineering (AMSE 2014), edited by: P.
Park, chapter, 1: Materials Science and Technology, October 1-2, Dubai, UAE, (2014), p. 3

Generally, the sintering phenomena occur below the melting temperature of polymer materials and hence sintering temperature is varied for different polymer materials.
It is evident from the table 1 that, PS necessitate more amount of heat than other materials.
The mechanical characteristics behavior of ABS materials is shown in Fig. 3.
Xuanhui, Structural and mechanical characteristics of porous 316L stainless steel fabricated by indirect selective laser sintering, Journal of Materials Processing Technology, 213 (2013) 838–843
Zuo, Simulation of temperature distribution in single metallic powder layer for laser micro-sintering, Computational Materials Science, 53 (2012) 333-339

All of them contain a group of selected material models, including the models of nonlinear hyperelastic materials, in their libraries.
However, this software does not offer analysis with a hyperelastic Zahorski material which allows for a more precise determination of the behaviour of rubber and rubberlike materials at significantly higher deformations compared to the widely used materials such as Mooney - Rivlin or neo - Hookean materials.
Selected Hyperelastic Potentials for Incompressible Materials With large deformations, each of rubberlike materials behaves in a specific manner.
With the popularity of hyperelastic incompressible materials (used in different fields of science and technology), Zahorski’s potential allows supplementing the results of calculations obtained previously for Mooney material.
Mooney, A theory of large elastic deformations, Journal of Applied Physics, 11, 1940, 582-592

Journal of Applied Polymer Science, 109:3087-3092 (2008) [6] K.W.
Journal of materials science.
Materials in medicine .21(12):3077-3083 (2010) [12] Y.Y.
Cai, Journal of Applied Polymer Science, 116: 2866-2873(2010) [14] H.S.
Materials and Design, 31: 3289-3298 (2010) [17] O.

And by the knowledge of the mechanics of materials, potential energy can be derived, as is shown in Eq. 2
The author assumes that two component materials are selected from alloy steel, casting tin bronze, hard alloy and gray cast iron, and the material parameters are shown in table 2.
Acknowledgment The authors would like to thank the National Natural Science Foundation under grant of No. 51175475 and the Innovation Fund of Zhejiang Province Science Technology Department under grant of No. 2011R09018-03 for the support to this work.
Zhao: Journal of Zhejiang Sci-Tech University, (2009) No.5, p.55.
Li: Journal of Dong Hua University (English Edition), Vol. 24(2007) No.1, pp.76

Construction and Building Materials, 200 (2019) 551-558
Journal of Thermal Analysis and Calorimetry
Fire Safety Journal. 81 (2016) 74-84
In: Аcs applied materials & Interfaces, 8-10 (2016) 6315-6319
Fire-resistant Heat Insulating Material with Variable Rheology IOP Conference Series: Materials Science and Engineering 661(1) (2019) 012106

Fray2,c 1 School of Materials Science and Metallurgy, Northeastern University, Shenyang 110004, P R China 2 Department of Materials Science and Metallurgy, University of Cambridge, Pembroke Street, Cambridge CB2 3QZ, UK a qianxu201@mail.neu.edu.cn, b cs254@cam.ac.uk, c djf25@cam.ac.uk Keywords: Ta-Nb alloy, molten salt, electro-deoxidation, FFC-Cambridge process Abstract.
Robin: International Journal of Refractory Metals & Hard Materials 17 (1999), 305
Nunes: International Journal of Refractory Metals & Hard Materials 24 (2006), 413
Fray: Journal of Materials Research 18 (2003), 346
Chen: Chemistry of Materials 19 (2007), 153

Journal of Magnetism and Magnetic Materials 272-276(2004) e1925-e1927
RARE METAL MATERIALS AND ENGINEERING,2014,43(11):2748-2752
Anisotropic powder from sintered NdFeB magnets by the HDDR processing route[J].Journal of Magnetism and Magnetic Materials,324(2012)63-67
Effects of Dy and Nb on the mag-netic properties and corrosion resistance of sintered NdFeB［J］．Journal of Magnetism and Magnetic Materials，2004，283( 4) : 353
RARE METAL MATERIALS AND ENGINEERING, 2010，39（10）：1777-1780