Search results

Owen, E.L.
[4] Mote et al., Williamson-Hall analysis in estimation of lattice strain in nanometer-sized ZnO particles, Journal of theoretical and applied physics 2012, 6:6
[7] Das et al 2012, Transparent conducting zinc oxide as anti- reflection coating deposited by radio frequency magnetron sputtering, Indian Journal of Physics 86 (2021) p23-29
Jiang et al, electromagnetic interferences shielding, Polymer Reviews (2019) 58 pages

Influence of silica and zirconia particles as filler loading on the radiopacity of dental resin composites SAAD OMAR ALSHARIF1a, HAZIZAN BIN MD AKIL1b, NASSER ABBAS ABD EL-AZIZ2c and ZAINAL ARIFIN AHMAD1d 1School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia,14300 Nibong Tebal, Penang, Malaysia 2Advanced Medical and Dental Institute, Universiti Sains Malaysia, 13200 Kepala Batas,Penang, Malaysia asaadelsharif@yahoo.com; bhazizan@eng.usm.my; cnasser@amdi.usm.edu.my; dzainal@eng.usm.my Keywords: Bis-GMA, TEGDMA, resin matrix, SiO2, ZrO2, filler loading, radiopacity.
However, the purity of aluminum step-wedges should be at least 98% (mass fraction) and the radiopacity should not be less than 0.5 mm Al of any value claimed by the manufacturer.

Armbrust, el al.

Huichun et al. [1, 2] adopted electronic nose technology to study Xihu Longjin tea in different levels.
Dutta, E.L.

El-Sayed.
Sreekumar et al. / J Zhejiang Univ Sci A.Vol.5(2007),p:818-829.

The following normalized power spectral density of the fluctuating wind speed has been proposed as Eq. (4) by Kaimal et al. [4] (4) where ω is the frequency in Hz, the parameter v* is the shear flow velocity which is determined by , where k is von Karman's constant (generally assumed to be approximately 0.4), and H0 is the roughness length, a variable characterizing the terrain.
The material properties of the composite laminated plate are: EL = 138GPa, ET = 8.96GPa, GLT=7.1GPa, ηL=0.42%, ηL=3.5%, ηL=4.4%, VLT= 0.3, ρ=2000Kg/m2.

References [1] Burns L D, Hall R W, Blumenfeld D E, el al.

Study of API 5L X52 Carbon Steel Treated in Oxygen Plasma Discharge DEMRI Boualem1, a, MANSOUR Dalila2,b 1Département des Sciences Fondamentales, Ecole Nationale Polytechnique, 10, Avenue Hassan Badi, El-Harrach, Algérie 2Laboratoire Corrosion, Division Laboratoires, Sonatrach, Avenue 1er novembre BP 35000 Boumerdès, Algérie ademrib@yahoo.fr, bd.mansour@hotmail.fr Keywords: plasma discharge, carbon steel, metallographic microscopy, SEM, EDS, XRD.
The material used in this study is API 5L X52 carbon steel, with the following chemical composition given by X Rays Fluorescence: 0.2 %C, 96.35% Fe, 0.078% Cr, 0.078% Ni, 1.179% Mn, 0.15% Si, 0.1715% Cu, 0.0423% V, 0.012% S, 0.01% P, 0.012% Al, 0.046% K and 0.07% Cl.

Take the acceleration response signals at A7 gauge point under the excitations of No. 2, 8, 17, 26, 35, 44 and 53 which are all based on El Centro record and suppose they are continuously sampled to get an acceleration response signal shown in the Fig. 1 (a).
Long, et al.: Proc.

[4] Al-Muntasheri, G.
A., Nasr-El-Din, H.A., and Zitha, P.L.J.2008.Gelation Kinetics and Perfor- mance Evaluation of an Organically Crosslinked Gel at High Temperature and Pressure.