Search results

Particle size control is also an important process in the production of powdered elastomeric materials.
Experimental Details Materials.
Properties of powder elastomeric materials.
Krasotkina, et.al., Development and properties of new nanomodifiers for road pavement, Russian Journal of Physical Chemistry B. 8 (4) (2014) 577-583. https://doi.org/10.1134/S1990793114040071 [2] ASTM D5644-18 Standard Test Method for Rubber Compounding Materials – Determination of Particle Size Distribution of Recycled Vulcanizate Particulate Rubber
Goljandin, Crumb Rubber as a Secondary Raw Material from Waste Rubber: A Short Review of End-Of-Life Mechanical Processing Methods, Recycling. 5(32) (2020) 1-20. https://doi.org/10.3390/recycling5040032 [5] Kravchenko I.B., Elastomeric materials containing a finely dispersed elastic filler obtained by the HTSG method: dissertation of a candidate of technical sciences: 05.17.06 / Kravchenko Ivan Borisovich., Moscow, 2008

The problem is that the waste consists of mostly non-recyclable materials.
Therefore, non-recyclable and difficult-to-recycle materials have to be replaced with environmental friendly materials.
Efforts in substituting non-recyclable materials with recyclable materials have been performed throughout the world.
Shen, Vibration and Damping Analysis of Composite Fiber Reinforced Wind Blade with Viscoelastic Damping Control, Advances in Materials Science and Engineering, (2015), Article ID 146949 [5] D.R.
Pal, Jute fiber reinforced epoxy composites and comparison with the glass and neat epoxy composites, Journal of Composite Materials, Vol 48, Issue 20 (2014), pp. 2537 – 2547 [10] H.

The objective of work is to produce ready to use nickel/carbon supported catalyst by easy, safety and low cost process Materials and Methods Cattail Flower pretreatment.
[5] Kanthana Klaigaew: Chemical Engineering Journal vol. 278 (2015), p. 166–173
(Ed.), New and Future Developments in Catalysis, Current catalytic processes with hybrid materials and composites for heterogeneous catalysis, Chapter, 4, Elsevier, Amsterdam (2013) p. 79-104
Assabumrungrat: Chemical Engineering Journal vol.278 (2015), p. 249–258
Huber: Journal of Catalysis vol.330 (2015), p.19–27

Materials and Methods Soybean Soybean used in the experiment was Kennong 42 provided by Heilongjiang academy of agricultural sciences.
Factor contribution rate is as follows: enzyme additive amount > hydrolysis time > modification time > materials to water ratio > succinic additive amount).
Innovative Food Science and Emerging Technologies. 8, 55-62
Journal of Food Lipids. 7, 237-245
Journal of Food Lipids. 7, 237-245.

Since, in laminated composites two dissimilar materials are bonded together, the laminates may tend to de-bond.
Further, the difference in thermal coefficients of the constituent materials may result in residual stresses.
The concept of FGM was proposed in 1984 by materials scientists as a means of preparing thermal barrier materials.
Pan, Exact solution for functionally graded anisotropic elastic composite laminates, Journal of Composite Materials 37 (2003) 1903–20
Soave, Refined and advanced models for multilayered plates and shells embedding functionally graded material layers, Mechanics of Advanced Materials and Structures 19 (2010) 604–622 [9] B.

Until now, prepreg sheets with thermosetting resin matrix are assumed to be used for materials in simulation software.
Materials and Experimental Procedures Self-weight Deflection Test Specimen.
Sone and T Katayama, “Evaluation of tensile property of CF/PA6 at molding temperature”, Journal of the Society of Materials Science, vol.67, (2018), pp.460-467
Katayama, “Formability evaluation and finite-element analysis of diaphragm molding for GFRTP with in-plane tension”, Journal of the Society of Materials Science, vol.67, (2018), pp.453-459
Boisse, “Thermomechanical analysis of thermoplastic composite prepregs using bias-extension test", Journal of Thermoplastic Composite Materials, vol.27, (2014), pp.679-698.

Field emmission scanning electron microscopy (FESEM) will be used for study of the surface morphology of materials synthesized in thin film form.
Before deposition process, cleaning of substrate plays important role, which prevents contamination of the sample allow for correct deposition of materials.
Elsaeedy, A low temperature synthesis of Ag2S nanostructures and their structural, morphological, optical, dielectric and electrical studies: An effect of SDS surfactant concentration, Materials Science in Semiconductor Processing, 93 (2019) 360-365
Lokhande, Photoelectrochemical investigation of Ag2S thin films deposited by SILAR method, Materials Chemistry and Physics, 72 (2001) 105-108
[16] Faisal Baig, Yousaf Hameed Khattak, Bernabé Marí Soucase, Saira Beg, Shafi Ullah, Effect of anionic bath temperature on morphology and photo electrochemical properties of Cu2O deposited by SILAR Materials Science in Semiconductor Processing, 88 (2018) 35-39

Fig. 1 Total production 260 000 tons all production processes (bio-composites: 350 000 tons production of wood and natural composites in the European Union 2012) [4] Huge amount of bio-materials are used in automotive industry (Fig. 1).
Material and parameters of cutting process Experiment was realized on the Wood Plastic Composite (in short WPC – Fig. 2, hybrid material composed of natural wood particle – more than 70 % and plastic matrix from polyethylene with high density).
Arora, in: Composites Part A: applied science and manufacturing, edited by Elsevier, volume 35, Elsevier (2004) [3] V.
Gowd: Indian Journal of Engineering & Materials Science Vol. 20 (2013), p. 385 [6] T.
Gowd: Journal of Advanced Mechanical Engineering Vol. 1 (2013), p. 1 [8] Z.

Journal of Materials Science: Materials in Electronics, 28, 4763-4771
Materials Science-Poland, 34(2), 437-445
Materials Science and Engineering: B, 292, 116421
Journal of Materials Science: Materials in Electronics, 32, 11547-11567
Journal of Materials Science: Materials in Electronics, 27, 10525-10531.

Experiments were carried out on both ejectors to observe their holding force on food materials as a function of mainly the pressure, flow of the primary air and other parameters.
When tested on thick bark/packed food materials, they left no suction marks on them.
Universal gripping of a wide variety of food materials still poses a challenge in many food industries.
When tested on thick bark/packed food materials, they left no suction marks on them.
Purnell: ‘Robotic Equipment in the Meat Industry’, Journal of Meat Science, Vol. 49 (1998), No. 1, pp.