Search results

Although, there is no precise evidence of the presence of Al substitution for Si in the chains due to signal overlap, we still refer to the calcium silicate hydrate as C─(A─)S─H, because the presence of Q2(Al) species cannot be excluded [18].
El Hafiane, J.P.

Sims, et al., The fabrication, properties and microstructure of Cu–Ag and Cu–Nb composite conductors, Mater.
Barsoum, T.El-Raghy, Synthesis and Characterization of a Remarkable Ceramic: Ti3SiC2, J.
Kooi, R.J.Poppen, N.J.M.Carvalho, et al., Ti3SiC2: A damage tolerant ceramic studied with nano-indentations and transmission electron microscopy, Acta Mater.. 51 (2003) 2859

Yamazaki et al.
Cezarino, A.L.
Stimulation of differentiation in sodium-dependent vitamin c transporter overexpressing mc3t3-el osteoblasts.

Experimental Study Of Drilling Composite Materials With Step-Core Drill, Materials And Design, N.29, P.1740–1744, 2008 [3] El-Sonbaty, I.; Khashaba, U.
[8] Jessy, K. et al.
[9] Campos Rubio, Juan Carlos et al.

Thiol-capped CdTe QDs were synthesized according to the method reported by Zhang et al.[11] with some modifications.
Andreani, E.L.
Talapin, A.L.

Wusatowska-Sarnek et al. [2] similarly report the presence of a <101> fibre compression texture at low temperatures, and although this component remained throughout a range of temperatures, it was found to weaken as the temperature increased.
An explanation of the texture weakening in copper at higher temperatures has been given by Hasegawa et al. [10], who found that an increase in temperature was accompanied by an increase in the frequency of twinning during grain boundary migration, and at very high temperatures, when the frequency of twins was large, the texture became random.
Vol. 15 (1999), p. 803 [6] E.L.

the formula for calculation as follow (Junichi Kamide and Li Changyou, 1991) (1) where, Q Air Volume (m3/s) Flow Coefficient (=0.622) A The hole area of Orifice ( m2) air specific weight () the pressure difference of U-Tube (mmAp) Air-Expansion modified coefficient the liquid height difference of U-Tube (mm) (2) Static pressure loss: The static pressure loss is calculated by the height difference of U-tube between the upper and lower chamber of drying tower，the formula for calculation as follow (2) where, static pressure loss (Pa) the tilt angle of U-gauge () the height difference of U-Tube (mm) (3) The ratio of air flux to grain mass: The size of air volume and the quality of dry-cereal are essentially unchanged during ventilation, so defines the ratio of air volume passing through the dryer and the weight of dry-cereal as the ratio of air flux to grain mass (Yang Zhou et al
Trans ASAE.1988.31(4):1237-1240 [6] Sokhansanj S,Falacinski A A,Sosulski F W el al.

As a different eutectic ceramic oxide system, rods with small diameters of the Al2O3/ZrO2(Y2O3) system have been reported by Sayir et al [4] and Paster et al [5] as having superior mechanical properties at high temperatures.
［9］ Courtright, E.L., Graham, H.C., Katz, A.P., and Kerans, R.J.: 1992, Materials Directorate, Wright Laboratory, Air Force Materiel Command, Wright-Patterson Air Force Base, 1

Fan, and el al, “Analysis and design of digital drawing management information system based on UML”, Mechanical Science and Technology for Aerospace Engineering,, Vol. 28 (3), pp. 404–411, March 2009 [2] F.
Tang and et al, “Data vault and document management in PDM based on workflow,” Computer IntegratedManufacturing Systems, vol. 10 (3), pp. 336–341, March 2004 [5] H.

Das et al (2009) [5] studied about Combustion analysis different blend proportion of Jatropha, Karanja and Polanga based biodiesel as fuel in a diesel engine.
Raghu et al [11].
However, simulations by FIRE v8.4 in bus engine MAN D2566 showed that spray angle appears to be almost the same for diesel and neat RO biodiesel spray Pogorevc, P. et al. [16].
According to Desantes et al. [18, 19] defined the spray angle as the cone angle formed by the spray consideringa60% penetration where they compare the influence of using biodiesels with conventional injection systems.
Spray angle of neat SO biodiesel at injection pressure of 50 MPa was 9%narrower than that of diesel by Alloca et al. [17].