Search results

The structure type of CaNb2Bi2O9, J.
The crystal chemistry and dielectric properties of the Aurivillius family of complex bismuth oxides with perovskite-like layered structures, J.
Journal of Solid State Chemistry. 164(2) (2002) 280-291
Dielectric classification of crystal structures, ionization potentials, and band structures, J.
Materials Chemistry and Physics. 113(1) (2009) 145-149

The secondary structure was evaluated by the Fourier transform infrared spectra.
Calculation of secondary structure.
The secondary structure of the specimen was calculated based on its amide I.
The area of each peak was correlated with the content of the assigned structure.
National Institute of Standards and Technology Chemistry Web Book: (2003), p

Influence of Acetylene Black Colloidal Solution on the Reactivation of the Simulation and Deactivation PbO2/PbSO4 Electrode Zhong-xu Dai1,2, a, Hui Zhan2,b, * , Jin-yun Zou2,c and Yun-hong Zhou2,d 1College of Chemistry and Life Sciences, China Three Gorges University, Yichang China, 443002 2College of Chemistry and Molecular Sciences, Wuhan University, Wuhan China, 430072 adaizx@ctgu.edu.cn, b,*zhanhui3620@126.com (corresponding author) Keywords: Acetylene black colloidal solution; PbO2/PbSO4 electrode; Regeneration.
ABC colloidal particles can be conducive to the structure improvement of the simulation deactivation PbO2/PbSO4 electrode.
It makes increase the proportion of micro holes gradually, and gradually formed the coral structure finally.
It can make the gap become bigger following the holes merger, the coral structure of the electrode can be destroyed as the progress of the charge and discharge cycles.
Therefore, ABC colloidal particles can be conducive to the improvement of the simulation deactivation PbO2/PbSO4 electrode structures.

The boron based layered structure represents a possible solution.
AlB2 and B2O3 have hexagonal crystal structure.
AlB2 has layered crystal structure which is similar to layered molybdenum disulphide (MoS2).
Journal of Solid State Chemistry, 2004. 177(2): p. 389-394
The Journal of Physical Chemistry, 1996. 100(25): p. 10739-10745

Fig.1 Schematic diagram of the moving-bed apparatus Results and discussion Changes of composition and structure before and after sample binderless briquetting The proximate and ultimate analysis of lignite and its briquette used for test are given in Table 1.
Briquetting basically has no effects on the chemical structure of samples, but the contents of oxygen functional groups are reduced in different degrees. bindless briquetting has no effect on composition and chemical structure, but change the surface structure of the lignite, and ultimately increase the volatile yield.
Coal chemistry [M].
Study of Structure and Components of Tar FromShenfu Coal [J].
Journal of Fuel Chemistry and Technology, 1995, 23 (1)

Fig. 1 Prior austenite grain identified in a martensitic matrix after Q&P processing Fig. 2 Physical simulation in a thermomechanical simulator Experimental Programme For this experiment, three new experimental steels were created whose special chemistries lowered the Ms and Mf temperatures (Tab. 1).
These chemistries were developed with the aid of the JMatPro software which had been used for calculating the approximate transformation temperatures.
Discussion of Results In most of the steels, the Q&P process produced (at higher partitioning temperatures of 250– 400 °C) predominantly tempered martensitic-bainitic structures with certain fractions of retained austenite (Figs. 3–8).
Upon slower cooling at 0.5 °C/s, martensitic structure with a higher fraction of bainite and a certain amount of retained austenite was obtained (Figs. 9, 10).
In most cases, tempered structures of martensite, bainite and certain amounts of retained austenite were obtained.

The nanotubes formed via anodisation growth allow a careful control over their structures uniformity, dimensions and pore size, obtaining structures vertically oriented from the surface.
At low voltage of 1 V, as seen in Fig. 1(a), no nanotubular structure can be observed.
As evidenced from the FESEM images in Fig. 1 (g) and (h), the anodised samples did not exhibit nanotubular structure; instead, a spongy-like structure with nanopores was formed.
Apparently, a mixture of tube-like structure at the upper part and porous structure at the lower part of the oxide layer was observed.
This mixture of structures gives rise to surface roughness which will increase the surface area.

The above results show that to increase the heavy metal ions removal capacities, the extraction chemicals may swell the cell wall more than water does and remove the cell wall components as well as extractives to change cell wall chemistry and architecture.
It shows that the swelling and exposing more xylose and lignin by breaking cell wall structure do play role in heavy metal ion removal.
Browning: Methods of Wood Chemistry (John Wiley & Sons, Inc., U.S.A. 1967)

The main objective of this work was to assess the use of flotation tailings and low-grade ore to biologically produce copper sulfide for further pyrometallurgical or fine chemistry processing.
The chemistry associated with the solubility of different metallic sulfides has allowed researchers to design novel strategies for the selective recovery of metals contained in acidic solutions [4,5,10,11].
The microbial structure of cultures used as inoculum for column tests was determined by qPCR.

Based on polycarboxylate chemistry, polycarboxylate superplasticizers (PCs) with hydrophobic side chains were synthesized through radical copolymerization reaction.
PCs have some advantages, such as the lower water/cement ratios, the controlling of molecular structure and the modulation of molecular weight.
From the structure of FM, the hydrophobic part of FM can be adsorbed on the surface [15], which is an entropy-driven spontaneous process [16].
Veazey: Handbook of chemistry and physics.