Search results

Fu, et al., A Potential Red-Emitting Phosphor BaGd2(MoO4)4:Eu3+ for Near-UV White LED, J.
Wang, et al., Red-light-emitting diodes fabricated by near-ultraviolet InGaN chips with molybdate phosphors, Appl.
Zhang, et al., Accurate measurement of refractive indices of Ca9La(VO4)7 crystal, Opt.
Stefanovich, et al., Ferroelectric and ionic-conductive properties of nonlinear-optical vanadate, Ca9Bi(VO4)7, Chem.
El-akrmi, M.

., et al., Morning sunlight reduces length of hospitalization in bipolar depression.
Wang, et al., Critical view on daylighting through solar bottle bulb.
El Essawya, et al., Green synthesis of graphene from recycled PET bottle wastes for use in the adsorption of dyes in aqueous solution.
Ongpeng, et al., Strengthening rectangular columns using recycled PET bottle strips.
Dombre, et al., Aromatic evolution of wine packed in virgin and recycled PET bottles.

%Al-1wt.
Experimental A bar of 30 mm in diameter from the alloy containing (wt %) 4.5 Al, 1.3 Zn, 0.5 Mn, 0.025 Cu, 0.002 Ni; 0.05 Si, 0.001 Be, 0.02 Fe, and Mg as a base was used as the initial material after pressing and annealing at 345 °C (1 h, cooling in air).
Mechanical properties (a-YS; b-EL) of MA2-1 alloy at Testing = 20 ºC after different regimes:1 - initial state; 2 - 4A ECAP and annealing;3 - 4Bc ECAP and annealing.
Gottstein and T.Al.

Effect of Laser Cutting Parameters on the Heat Affected Zone and on the Boundary Layer in Steel Laser Processing AGGOUNE Samia1,a*, ABID Cherifa2,b and AMARA El Hachemi1,c 1Advanced technologies development center, Laser material processing team, B.
Miraoui et al, have given the suitable parameters to get better quality of cut.
Vicanek et al
Raza et al., Laser cutting of 7050 Al alloy reinforced with Al2O3 and B4C composites, Te International Journal of Advanced Manufacturing Technology. vol.50, no.1–4, (2010) 185–193
[11] Al-Ali, H.H. and Selim, M.S.

Influence function methods (IFMs) were developed by Ren et al. 1987 [6] and are used extensively [5,7] to predict mining subsidence.
Al Heib, J.P.
El Shayeb: Paramètres d’affaissement pour la hiérarchisation des zones à risque dans le bassin ferrifère lorrain.

Included in the figure are the present experimental data on ductility at 393 K and room temperature data on the elongation to failure that were reported by Torre et al. [1].
The values of strain to failure measured in the present investigation are much higher than those reported by Torre et al. [1].
Included are room temperature data by Torre et al. [1] and the prediction of the model of dislocation accommodated boundary sliding [7].
First, Wang et al. [3] reported that the presence of bimodal grain distributions and deformation twins in most of the large grains led to a high tensile ductility in nc-Cu.
El-Sherik and U.

Comparable publications [14; 15] define the Line Energy as El=P/v [J/mm] in order to approach this connection.
C., et al.: Direct-write 3D printing of NdFeB bonded magnets.
C.; Rios, O., et al.: Big Area Additive Manufacturing of High Performance Bonded NdFeB Magnets.
H., et al.: Binder Jetting: A Novel NdFeB Bonded Magnet Fabrication Process.
-C.; Gherekhloo, H.; Kasperovich, G., et al.: Microstructure of γ-titanium aluminide processed by selective laser melting at elevated temperatures.

DOI: 10.1088/1757-899X/192/1/012009 [6] Ferro C. et al.
[7] Emmelmann C. et al.
K. et al.
[10] Zhang P. et al.
DOI: 10.1007/s12540-018-0040-8 [24] Popovich, A.A., Razumov, N.G., Gyulikhandanov, E.L.

The aluminium such as Al 6063 is most popularly used for the mechanical parts.
The workpiece material is aluminium (Al 6063) with the size of 64 mm x 64 mm x 45 mm.
Abou-El-Hossein, B.
Abou-El-Hossein, K.

The experimentally obtained gradient in composition is compared with the predicted gradient, calculated from a kinetic model developed by Put et al. [10].
The indentation fracture toughness was calculated from the radial cracks originating from the corners of the HV10 indentations according to the formula of Anstis et al. [11].
Ti(C,N) content (vol %) El.
This calculation was performed, based on the equations derived by Suresh et al. [13] with the material data given in Table 5.