Search results

Anaerobic materials which polymerize in area of thread contact of parts are used.
There are data about influence of anaerobic materials on cyclic robustness of bolted joints [11, 12].
Cand. tech. sciences, Penza, 2002, 143 p
An engineering Journal”, Mashinostroenie, Moscow 2 35 (2000) 9–12
Voyachek, Assembly of threaded joints using anaerobic materials / I.I.

The properties of these materials are finally compared in the final discussion.
Table 2 lists the FoM for different TCO materials.
The tested materials remained stable with no increase in sheet resistance for temperatures slightly above the deposition temperature.
Kulshreshtha, Indium-Tin-Oxide transparent conducting coatings on silicon solar cells and their ‘figure of merit,’ Solar Energy Materials, 4 (1981) 151–158
Znaidi, Sol–gel-deposited ZnO thin films: A review, Materials Science & Engineering B, 1–3 (2010) 18–30

The wear forms of friction materials at low temperatures are mostly adhesive wear and abrasive wear.
Metal components in the composite friction materials, such as iron and steel fiber, when they contact directly, and slide under certain pressures, the atoms of iron on the friction interface between the iron and steel fiber are easy to adhere; the adhesive points have been cut and adhered repeatedly, they are likely to form abrasive dust and break off, so that minute steel fibers are to be pulled out or partially torn, and cast iron materials may also be adhered or torn, therefore, resulting in wear and the Number of samples Sample size [mm] Total area of the test [cm 2 ] Dual-rotation Test pressure [Mpa] Temperature range [℃] Drum (disc) speed [r/min] Friction line speed [m/s] 2 25×25 12.5 Plane friction disc 0.5 100~350 480 7 formation of abrasive dust.
Serious adhesive parts are usually with larger abrasive dust, at the same time, materials around the adhesive points are easily to be torn off and form massive loss, as shown in Fig. 3 (A).
Li: Journal of Materials Science and Engineering Vol.18 (2000) No.6, p.125-130 [2] G.P.
Hu: About Chinese automotive friction material status.

Cordierite–mullite composites were prepared by using iron tailing, burn talc, suzhou soil, knar clay and alumina powder as raw materials.
Expriment 1.1 Synthesis The starting raw materials used in this study are given in Table 1.
Journal of Mining Science, 2006, 42(4): 403-408
Metal recovery and inorganic eco-materials from tailings by leaching-sintering process [J].
Advances in Metallurgical, Processes and Materials, Ukraine, 2007, 337-343

Jaiswal, “Biodegradable magnesium alloys for orthopaedic applications: A review on corrosion, biocompatibility and surface modifications,” Materials Science and Engineering C: Materials for Biological Applications, vol. 68, pp. 948–963, 2016
Manuel, “Investigation of the mechanical and degradation properties of Mg-Sr and Mg-ZnSr alloys for use as potential biodegradable implant materials,” Journal of the Mechanical Behavior of Biomedical Materials, vol.7, pp. 87–95, 2012
Reifenrath et al., “Biodegradable magnesium implants for orthopedic applications,” Journal of Materials Science, vol. 48, no. 1, pp. 39–50, 2013
Zheng, X.N.Gu, F.Witte, “Biodegradable metals,” Journal of Materials Science and Engineering: R: Reports, Volume 77, March 2014, Pages 1-34 [6] Kumar, K., Das, A., & Prasad, S.
Materials Science and Engineering C 39, 315–324

British COMPAK equipment company was the earliest one to study using wheat straw and rice straw as raw materials.
Manufacturing technology of using wheat straw, rice straw and other non-wood materials as raw materials has become a project worked by a number of domestic research institutions and universities.
Journal of Huazhong University of Science and Technology (Urban Science Edition), 2005, 22(4): 25-27.
Henan Building Materials. 2011. (1): 97-98.
Journal of Nanjing Forestry University (Natural Sciences Edition).2005.29(6): 109-113.

Introduction Some material parameters, such as the deformation modulus , the Possion ration , the cohesion , the internal friction angel and so on, are very important and indispensable for evaluation to structural stability.
Acknowledgments The research presented in the paper is supported by the Project of Natural Science Foundation for the Youth from People’s Republic of China (NO.10902118).
Journal of Computational and Applied mathematics, 191(2006), 269-279
Science,220 (1983),671-680
Journal of Computational and Applied Mathematics, 129 (2001), 15-35

Adeyemi 'Experimental determination of heat transfer Coefficients during Squeeze casting Aluminium’, Journal of materials processing technology, Vol.209, (2009), pp 1477-1483
M, Pillai R.M, Pai.B.C ‘Studies on squeeze casting of Al 2124 alloy and 2124-10% SiCp metal matrix composite’, Materials Science and Engineering A, Vol. 490 , (2008), pp 235–241
[11] Yang.L.J ‘The effect of solidification time in squeeze casting of Aluminium and Zinc alloy ‘Journal of materials processing technology, Vol. 192 -193, (2007), pp 114 -120
‘Squeeze casting: an overview’, Journal of Materials Processing Technology, Vol.101, (2000), pp 1-9
Skolianos, Grigoris Kiourtsidis, Thomas Xatzifotiou ‘Effect of applied pressure on the micro structure and mechanical properties of squeeze cast aluminium AA6061 alloy’, Materials science and Engineering A, Vol. 231, (1997) pp 17 – 24.

Now China mainly uses reasonable energy-saving building materials to control the energy consumption of buildings.
In recent years, the composite energy-saving wall, which is made up of  thermal insulation materials, traditional wall materials and new-type composite wall materials, has been widely utilized in construction industry.
Its main materials include organic, inorganic and metal thermal insulation materials.
While taking full advantage of the natural lighting, we can achieve the aim of thermal insulation and ventilation. 4.2.1 The reasonable choosing of external window materials of building With different external window materials of building, the thermal insulation properties is different greatly.
So firstly, we should choose materials with smaller resistivity as wire, such as copper core cable.

Synthesis of BaTiO3 Nanorods at Room Temperature and Normal Pressure Tieyu Sun1, Xiaohui Wang1,a, Xiaoquan Zhang1 and Longtu Li 1,b 1 State Key Lab of Advanced Ceramics & Fine Processing, Department of Materials Sciences & Engineering, Tsinghua University, Beijing, 100084, China a wxh@mail.tsinghua.edu.cn, bllt-dms@mail.tsinghua.edu.cn Keywords: Barium titanate, nanorods, oleic acid Abstract.
Of course, the industry need more and more fine crystalline barium titanate as raw materials.
The raw materials of twice experiments.
We did twice with different proportioning of raw materials as shown in Table 1.
Bell: Journal of Applied Physics, Vol. 89 (2001), p. 3907-3914