Search results

These standards do not seem to apply in tropical climate where wall thick nesses are comparatively smaller (between 100 and 230 mm), and are usually of less dense materials.
Types and Sources of Data The study relied on two types of data, namely: i) Primary data physically obtained from the model buildings (comfort factors); ii) secondary data such as thermal comfort indices, insulating properties of materials, etc, obtained from design manuals, charts, standards, etc.
This goes to confirm the widely held view that materials with low heat capacity minimize heat storage in building envelop.
D Dissertation submitted to the Faculty of Environmental Sciences, Imo State University, Owerri, Nigeria.(2006)
Energy in Construction, Journal Stroitelvo No. 4, Sofia. (1984).

Devyatykh Institute of Chemistry of High-Purity Substances of Russian Academy of Sciences, 49 Troponina St, Nizhny Novgorod, 603950, Russia ae.titov@nntu.ru, borgchim@nntu.ru, ckutyin@ihps.nnov.ru Keywords: Chloroform, electrical discharges, Gibbs energy minimization method, chemical plasma model Abstract.
Introduction Organochlorine compounds are used as the basis of composite materials, solvents, detergents, dielectric media.
Panliang, Dechlorination and decomposition of chloroform induced by glow discharge plasma in an aqueous solution, Journal of Hazardous Materials. 308 (2016) 84-90
Rusanov, Slag-free process for plasma reduction of uranium from oxide raw material, Fizika i himiya obrabotki materialov. 4 (2000) 46–54
Jaramillo-Botero, CCl Radicals As a Carbon Source for Diamond Thin Film Deposition, The Journal of Physical Chemistry Letters. 5 (2014) 481-484.

Materials and methods The test materials. (1) The plant additive are dry wheat straws, wheat shells, corn leaves and corn cobs.
Acknowledgements This work was financially supported by the National Natural Science Foundation of China (51269008) and the doctoral scientific research foundation of Lanzhou University of Technology（0906ZXC122）.
Shenyang:Journal of Shenyang Agricultural University, 2010,41(3): 357-359.
Journal of Huazhong Agricultural University,2002,21(3):46-51.
Planting Materials seed systems of finger millet, rice and taro in jumla,kaski and barn districts of nepal[J].

Thus its distortion process needs to consider the inertia effect of the structure and strain-rate effect of the material under high load speed rate.
Explosives and air units use Lagrange- Euler multi-material algorithm, and cylinder unit use Lagrange algorithm.
The causes of shear pattern break are material within the micro shear zones and centralized macro shear band.
Journal of Applied Physics , 1968 ， 30 : 315～321
International Journal of Mechanics Science ， 1969 ，11 : 545 —549.

Measurement Principle Based on the Lambert's absorption law, for intrinsic semiconductor material GaAs, its absorption characteristics can be described as [ ]xRIxI )(exp)1(),( 0 θα θ −−= , (1) where 0I is the incident intensity, x is the thickness of semiconductor absorption material, R is the reflection factor of semiconductor material at the incident plane, θ is the temperature and )(θα is the absorption coefficient at the temperature θ.
For GaAs semiconductor material, Kb 300= KeV a /4 108.5 − ×= , eV Eg 522.1)0( = .
Refractive index of GaAs material is so high that probe can be designed in very small size without covering.
Chow: Journal of Vacuum Science Technology, B, Vol. 15 (1997), p. 329
Li: Journal of Transducer Technology, Vol. 20 (2001), p. 50

Wall material of Shangde Village is mainly solid clay brick which is restricted to be used by China.
Straw-bale as material for wall.
(3) Make the most use of surplus stem, process them into straw-bale which could be used as building materials
Acknowledgements This work was financially supported by the Science and Technology Research and Development Plan Project of Hebei Province (0921039B).
Inst (1986), p. 127 [2] Hong Jin, Hua Zhao, Xiuping Wang: Journal of Harbin Institute of Technology Vol. 38 (2006), p. 2108 [3] Shuyang Wang, Kun Song: Architectural Journal (2009), p. 93 [4] McNicholl, A, Lewis, JO: Energy and Buildings Vol. 33 (2001), p. 213 [5] Brian A.Rock: Energy and Buildings Vol. 25 (1997), p. 63 [6] Guozhu Li,Shuwen Niu，Libang Ma: Renewable Energy Vol. 34 (2009), p. 1438

Experimental Materials.
Mechanical Properties of Polylactic Acid and Natural Rubber Blend using Calcium Carbonate and Vetier Grass Fiber as Filler. (2012) 18TH International Conference on Composite Materials
Progress in Polymer Science.
Journal of Metals, Materias and Minerals.
Journal of Thermoplastic Composite Materials.

In this context, the paper defines an approach to analyse the relationships between different innovation categories (materials, function, etc.) and the relative environmental impacts (energy and water consumption, CO2 emission, etc.), during the product lifecycle.
Function, material, process, shape, and electronics are the most common classes used to model a product.
The results relative to three different solutions (Hygroscopic material, Foam glass, Photovoltaic) are shown in the Fig. 1.
The analysis of such a matrix, for example, allowed the company to evaluate the great environmental advantages provided by the use of the hygroscopic materials for the dishwasher.
Chen: Accelerating preliminary eco-innovation design for products that integrates case-based reasoning and TRIZ method, Journal of Cleaner Production Vol. 19 (2011), pp. 998-1006 [4] E.

Introduction The main existent techniques for repair and strengthen reinforced concrete (RC) beam-column joints can be grouped as follows: repair with epoxy (injection of epoxy resin in the cracks of lightly degraded elements); removal and replacement of concrete in more damaged areas; jacketing with RC layers, masonry blocks or steel plates; use of composite materials.
The main characteristics of these materials can be found elsewhere [2].
The authors acknowledge the materials generously supplied by Hilti Portugal – Productos e Serviços Lda., S&P Clever Reinforcement Ibérica Lda. and SECIL.
Zureick: ACI Structural Journal, Vol. 102, No. 2, (2005), p. 1-14
Costa: Journal of IBRACON de Estruturas e Materiais, RIEM, Vol. 4, Num. 1, (2011), p. 147-172.

The material parameters of the beam are E = 197 GPa, ν = 0.33, and ρ = 7900 kg/m3, while those of the PZT are E = 67 GPa, ν = 0.33, ρ = 7800 kg/m3, d31 = 1.7119 10-10 m/V, and δ33 = 2.03 10-8 F/m.
Crawley, J. de Luis: AIAA Journal 25 (1987), p. 1373-1385
Schmidt: in Advances in Computational & Experimental Engineering & Science, eds.
Atluri, A.J.B Tadeu, p. 439-444, Tech Science Press, 2004
Reddy: ASME Journal of Applied Mechanics 55 (1988), p. 611-617