Search results

Carrier gas is important in which raw materials produced without carrier gas contained many impurities of amorphous carbon and a number of carbonaceous particles around the CNTs, which have not formed CNTs [9].
Based on reported study, formation of bimetallic catalyst of Co and Fe probably assist in homogeneous dispersion of metal particles of support materials in the formation of higher quantities of CNTs [8].
The SEM micrographs of the MWCNTs shown in figure 1 demonstrated that MWCNTs grew densely over trimetallic catalysts with starting material of palm DHSA.
Salmiah, International Journal of Engineering and Technology 3 (2006) 115-124
Li, Materials Letters 60 (2006) 159-163

In particular, lightweight materials are in demand for carbon dioxide emissions reduction.
Kim, "Continuous Casting and Rolling for Aluminum Alloy Wire and Rod", Materials Science Forum, 638-642(2010)255-260
Jabłoński, Effect of Iron Addition to Aluminium on the Structure and Properties of Wires Used for Electrical Purposes, Materials Science Forum, 690(2011)459-462
Gold, Solidification Conditions and Microstructure in Continuously Cast Aluminum JOURNAL OF METALS April 1982, Volume 34(1982)28–34
[10] Toshio Haga, Ryusei Tahara, Hisaki Watari, Shinichi Nishida, Casting of Wire Using a Twin Wheel Caster, Key Engineering Materials, 904(2021)137-142.

Journal of Shenyang Jianzhu University,2010,20(5):892-896 [2]Linfeng Lu.Staggered truss steel framing system analysis and design method.
Journal of Building Structures, 2000,21(6):49-54 [4]Yin Pan,Xuhong Zhou.Aseismic behavior of the staggered-truss system.
China Civil Engineering Journal, 2002,35(4):12-16 [5]Linfeng Lu,Qiang Gu.Staggered truss joints design method.
Building Science Research of Sichuan, 2005,31(5),25-29 [6]Kang Ye,Guoqiang Li.Summarizing in Research for Semi-rigid Connectionins for Steel Frame structures.
Journal of Xuzhou Institute of Architectural Technology, 2011,11(2):24-26

Introduction In China, masonry structures are widely used as residence, school and office building because of its easy obtainment of material, simple construction technology and low cost.
Acknowledgements This work was financially supported by Beijing Natural Science Foundation (8142015).
China civil engineering journal: 2012, S2: 103-108
Journal of building structures: 2012, 33(11):62-71 [7] Yiling Liu, Tiejun Qu.
Journal of north China University of technology: 2013.03:88-94

This model uses the same material with real bridge to ensure the elastic modulus, Poisson's ratio and the real bridge unity.
JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH. 1991, 18(1): 45-54
(Natural Science Edition) 2010(05): 117-120.
Model tests on steel-concrete joining section of main girder of a cable-stayed bridge [J] CHINA CIVIL ENGINEERING JOURNAL: 2006, 39(3): 86-90.
Mechanical features of cable-girder anchorage for cable-stayed bridgeswith steel box girders[J] CHINA CIVIL ENGINEERING JOURNAL: 2012, 09: 100-107.

Material Aluminum 6061 Modulus of Elasticity (Pa) 7.07 e+10 Density (kg/m3) 2700.0 Mass (kg) 0.387 Length (mm) 1000.0 Width (mm) 40.0 Thickness (mm) 4.0 Table 2.
V. and Counts, J., “Deflection of a Beam Carrying a Moving Mass,” Transactions of the ASME, Journal of Applied Mechanics, Vol.41, pp.803-804, 1974
H., “A General Algorithm for Moving Mass Problem,” Journal of Sound and Vibration, Vol. 33, pp. 49-58, 1974
I., “Dynamic Behavior of a Finite Beam Subjected to Travelling Loads with Acceleration,” Journal of Sound and Vibration, Vol. 55, No. 1, pp. 65-70, 1977
S., “Dynamic Behaviors of an Elastically Restrained Beam Carrying a Moving Mass,” Journal of Mechanical Science and Technology, Vol. [20, No. 9, pp.1382-1389, 2006.

Experiment of Two Models of Hypoxia Training, and Their Influence on Rats’ Cardiovascular System Wei Liu Department, Xi’an University of Science and Technology, Xi’an, 710054, China.
Testing material and index testing methods.After the training, cut their tail to draw blood of 3 ml for RBC and HCT test.
References [1] Ye Ming.Journal of Physical Education,2010(7)
[3] Gao Tao.Chinese Journal of Medicine ,2005,5(2)245-246 [4] Yin Wei Na.Journal of capital institute of physical education,2005,5(3)115-117
Journal of xi'an institute of physical education 1997，14(2)：79-81.

The component parameters consist of material, dimension, roughness, surface treatment, heat treatment, etc..
The domains of knowledge involve in dynamic, statics, materials science, machining, and so on.
The ontology concepts models represent the design results including the topological structures, materials, process requirements, etc..
[5] Jinrui Gu and Fang Wang: Information Science, Vol. 25, No. 6 (2007), p. 949–956.
[7] Xin Shi, Shurong Tong, Fei Ma: Journal of Mechine Design, Vol. 28, No. 1, (2011) p. 1–4.

Gupta:Materials and Manufacturing Processes(2010)25: 777-785 [4] W.Q.
:China Railway Science. (1994)12: 87-95(in Chinese)
SHI, :Journal of the China Railway Society,(1995)12: 92-95(in Chinese)
:Journal of the China Railway Society,(1999)6: 72-75(in Chinese)
WAN:China Railway Science, (1999)9: 20-28(in Chinese)

Acknowledgements This research is financially supported by Forest Science and Technology Innovation Program of Guangdong Province (Grants: 2010KJCX012-02 and 2011KJCX031-02) and a cooperative grant from Dongguan Research Institute of Forestry.
Science, 1999, 284: 105-107
Journal of Environmental Management, 2000, 58(4): 269-287
Advanced Materials Research, Vols. 518-523 (2012): 5335-5340
Advanced Materials Research, Vols. 518-523 (2012): 5324-5329