Search results

El-Deiry, R.P.
Dinesen, A.R. et al, ed., Risφ National Laboratory, Roskilde, Denmark. (2001)

This kind of paper, whose density is 110  10 g/m 2, Young's Modulus in longitudinal direction is EL =3075  50 MPa and transverse ET = 797  20 MPa, and ultimate stresses UL = 17.5  0.4 MPa and UT 4.73  0.35MPa, has a well defined anisotropy in its mechanical properties associated with a preferential orientation in the Machine Direction (MD) of the fibers on the macroscopic size.
Hinojosa et al.[17] analyzed morphological self-affine properties in a glass material.

[13] M.A.Yahya, Z.Al-Qodah, C.Z.Ngah, Agricultural bio-waste materials as potential sustainable precursors used for activated carbon production: a review, Renewable and Sustainable Energy Reviews. 46 (2015) 218235
[21] G.Chu, J.Zhao, Y.Huang, et al., Phosphoric acid pretreatment enhances the specific surface areas of biochars by generation of micropores, Environmental Pollution. 240 (2018) 1-9
[22] S.M.Yakont, El-Deen G.Sharaf, Characterization of activated carbon prepared by phosphoric acid activation of olive stones, Arabian Journal of Chemistry. 9 (2016) 155-162
-A.Wu, M.Wang, et al., Preparation of activated carbon from a renewable agricultural residue of pruning mulberry shoot, African Journal of Biotechnology. 9(19) (2010) 2762-2767

Shi (Ed), NanoScience in Biomedicine, Springer-Verlag GmbH, Heidelberg, 2009, 21-42 [6] A.L.
El Zowalaty, G.K.
Al-Deyabd, Q.
Pinzon-Garcıa et al., Efficient cutaneous wound healing using bixin-loaded PCL nanofibers in diabetic mice, Biomed Mater Res Part B (2016) 1-12 [45] L.R. 

Risfaheri et al. narrate the pyrolysis procedure of CNSL.
Pushparaj et al. used bio additive called Bio Fuel Enhancer (BFE) with karanja biodiesel blend and found anticipated results [18].
The main components of the experimental set up are combustion pressure and volume measurement (piezo electric sensor and shaft encoder) fuel flow sensor unit, electrical loading arrangement, voltmeter, ammeter, cooling water sensor unit and air flow sensor unit .The outlet temperatures of cooling water and exhaust gas were measured directly from the thermocouples (Cr–Al) attached to the corresponding passages.
El-Diwani, N.K.

Arbaoui et al. (2014) show that the bending stiffness increased clearly with increasing the polypropylene honeycomb core from single to double core [8].
According to Xinni Mou et al. (2019), the compressive strength increases from 1.536 to 1.698 N/mm by increasing the honeycomb paperboard thickness from 10 to 50 mm [17].
Arbaoui et al. (2014) [8].
El Mansori, B.L.

J Y Park[5]et al have reported the Amberlyst-15 and Amberlyst BD20 catalysts, which showed good catalytic efficiency for high free fatty acid oil.
S Furuta [6] et al found that WO42-/ ZrO2/Al2O3 has higher activity for both the transesterification of soybean oil with methanol at 250 ˚C and the esterification of n-octanoic acid with methanol at 175-200 ˚C; but it is expensive because zirconium is a rare and costly metal.
Qing shu et al [7] prepared a La/ β-zeolite catalyst by ion exchange method, which shows higher conversion of triglyceride and stability than zeolite beta for the production of biodiesel.
The carbon, hydrogen and nitrogen contents were determined using an Elementar vario EL analyzer.

The simulation model of the plasticity deformation during the cold roll-beating was established by Kurz.N [2] et al based on the finite element theory, and the forming force, stress value and strain value of the workpiece was calculated.
The method of finite element was employed by Zella.L.Kahn-Jette[3] et al to analyze the contact condition of the involute spline under the axisymmetric loading and non-axisymmetric loading, and the changes of the stress and strain in the increasing torque and the stress concentrating distribution are showed.
Ehab, El-Danaf, M.
Almajid, Effect of Solution Heat Treatment on the Hot Workability of Al –Mg-Si Alloy, Materials and Manufacturing Processes, vol. 6, no. 24, pp. 637-643, December 2009

Subsequently, Oleksiak et al. [10] synthesized metastable GIS zeolite via organic-free routes for gas separation purposes.
In another work, Maldonado et al. [11] also managed to obtain GIS zeolite without polymorphs after running hydrothermal synthesis for 7 days at 100°C.
Synthesis of GIS zeolite For the formulation of GIS zeolite, 2.94 g of sodium aluminate, 12.20 g of sodium silicate, 7.67 g of sodium hydroxide and deionized water were added into the propylene bottles according to a molar ratio of 3.7 Si:0.41 Al:10 NaOH:173 H2O [18].
Accelerated Synthesis of dodecasil 3 rhombohedral (DDR3) zeolite cyrstals via hydrothermal growth coupled with ultrasonic irradiation method, RSC Adv 2015;29:22658-22664 [5] First E.L., Hasan M.M.F, Floudas C.A., Discovery of novel zeolites for natural gas purification through combined material screening and process optimization, AICHE J, 2014; 60:1767-1785

El-Mashade, S.M.
Sato et al., Development of pure green LEDs based on ZnTe, physica status solidi (a). 1 180 (2000) 267-274
Kekelidze et al.
Georgobiani et al., A fine structure of the edge ultraviolet luminescence of the nitrogen plasma activated GaN: Mg films and the ZnO–GaN: Mg electroluminescent heterostructures on their base, Semiconductors/Physics of the Solid State. 6 35 (2001) 725-730