Search results

Kindrachuk, Wear resistance of VT22 titanium alloy after nitriding combined with heat treatment, Materials Science. 52.1 (2016) 56-61
Lütjering, Influence of processing on microstructure and mechanical properties of (α+ β) titanium alloys, Materials Science and Engineering.
Short, Gas tungsten arc welding of α+ β titanium alloys: a review, Materials Science and Technology. 25.3 (2009) 309-324
Mayorova, Influence of Gas Dynamic Processes on Chemical Composition of Hardfaced Layer when Restoring Machine Parts Manufactured from 40H Steel, Materials Science Forum.
Chen, Effect of heat treatment on microstructure and mechanical properties of a new β high strength titanium alloy, Materials & Design. 55 (2014) 183-190

Acoustic emission (AE) technique was used to investigate fatigue crack growth on compact tension specimens of aging materials at room temperature.
Test materials have been sampled steam pipe serviced the actual operation conditions for a long time in fossil power plant.
Moreover, it takes much time and resources to inspect the pipe since the lagging materials around the pipe must be removed and reinstalled.
Methods of the Test A335 P22, which has been seviced as the main steam pipe materials for a long period of time, were designated as test materials.
Therefore, it was confirmed that crack growth ratio of in-serviced materials can be evaluated by acoustic emission method.

Journal of Sound and Vibration 142 (1990): 49-75 [5] G.
Journal of Sound and Vibration 185 (1995): 743-765 [6] K.
Journal of Sound and Vibration 226 (1999): 469-492 [8] S.
Journal of Sound and Vibration 229 (2000): 287-310 [9] S.
Journal of Engineering for Industry 99 (1977): 785 [15] C.

Ultrasonic inspection is the most successful non-destructive testing technique for detection of flaws in engineering materials.
Introduction Ultrasonic inspection is the most successful non-destructive testing (NDT) technique for quality assessment and flaw detection of engineering materials.
This study utilizes advanced signal processing and pattern recognition techniques to aid ultrasonic inspection for identifying different flaws found in carbon fiber reinforced polymer (CFRP) materials.
Acknowledgements This work was financially supported by the Natural Science Foundation of JiangXi Province (No. 20122BAB201039), the Foundation of Key Laboratory of Nondestructive Testing (Nanchang Hangkong University), Ministry of Education (No.
Selvakumar: Journal of Nondestructive Evaluation Vol. 30 (2011), p. 20-28 [3] Abdulhamit Subasi and M.

Adjust measures to local conditions, use local materials, so there is no definite construction patterns and rules.
Architecture structure form adopts concrete shear wall structure, exterior wall material for insulation check wall, from the inside to the outside of 190 thick shale hollow brick, 80 thick benzene board, and 90 thick shale hollow brick.
Summary Through to analyze energy-saving technology of green residential building in Shenyang, including the low energy consumption space enclosing structure system, chamber control radiant floor heating system and solar energy hot water system shows: Choose insulation materials with the average heat transfer coefficient of 0.25 (W/m2k) and outside the window with 2.2 (W/m2k), and control the quality of construction technology strictly, it can make architectural energy saving efficiency more than 65%.
Architectural journal, 2007 (12): 11 to 15.
In Chinese [6] China construction science research institute.

Starting Materials, Processing and Forming.
The work had involved considerable planning and lots of samples preparation and examination of the materials.
Coble: Journal of Applied Physics Vol. 41 (1970), p. 4798, 5.
The full paper is being written up for submission to the ASEAN Journal of Science and Technology for Development for publication in the 2009 Edition. 10.
Hing, Invited Lecture on Materials Development for High Intensity Discharge Light Sources, presented at the 5 th International Conference on Materials Processing for Properties and Performance, Dec 2006. 11.

Additionally, if there is a more detailed comparison among gross domestic product, use of raw materials and footprint density trends, then the relationship between economic growth, use of raw materials and ecological pressure can be revealed.
Environmental Science & Technology, 45 (2011).
Environmental Science & Technology,45(9)(2011).pp: 4088-4095
The International Journal of Life Cycle Assessment, 11(3) (2006), pp: 189-199
Journal of Industrial Ecology, 18(1) (2014) pp:20-23

With the emergence of new materials, as well as numerical control machine tools and the extensive use of flexible manufacturing systems, relying on personal experience to determine the cutting parameters can not meet the development of the times.
Along with the development of science and technology and computer application increase in machining processes, computer technology is used to develop cutting database.
“A system for optimising cutting parameters when planning milling operations in high-speed machining”.Materials Processing Technology. 168(2005). pp.25–26
Materials Processing Technology. 209(2009),pp.107–108 [9] Ihsan Korkut , Mehmet Boy , Ismail Karacan. ”Investigation of chip-back temperature during machining depending on cutting parameters ”.
Materials and Design,pp.28(2007) 2334–2335

Introduction Now the resin matrix composites are very important materials applied in different areas.
Different environmental conditions affect the properties of composite materials and determine their service lives.
So many researches are focusing on the effect of accelerated aging on the properties of composite materials.
Boukhoulda, et al. [3] investigated aging-impact coupling upon the polyester matrix E-glass fibers composite materials in hygrothermal environment.
Lousdad: Materials and Design,2011( 32), p. 4080 [4] Salar Bagherpour, Roholah Bagheri, Ahmad Saatchi: Materials and Design, 2009(30), p. 271 [5] Y.Z.

The materials that had been used for aircraft usually have low dielectric constant and high toughness composite [2].
Materials are lay-up into mold and vacuum is applied before resin is introduced.
Materials.
Information http://engineer.jpl.nasa.gov/practices/2205.pdf [5] M.Y.Haris, D.Laila, E.S.Zainudin, F.Mustapha, R.Zahari, and Z.Halim, preliminary review of biocomposite materials for aircraft radome application, Key Engineering Materials, 471-472 (2011) 563-567
Murat Sozer, variation of part thickness and compaction pressure in vacuum infusion process, Composite Science and Technology 69 (2009) 1710-1719.