Search results

Experiment Materials.
Reference [1] Xiaokunqi, HaoXiaoXiu：Printing Materials ( Chemical Industry Press, Beijing 2009) [2] Katristsis d, in the flower, HuangYuJiang, WuGuanYing: Packing Manual (China petrochemical publishedClubs, Beijing 2002) [3] SunCheng bo, Silica Rheological Characteristics and Dispersion Models[D], Beijing Institute of Graphic Communication, 2007; [4] YangJianWen, CengZhaoHua, ChenYongLie.: Light Curable Coating and Application (Chemical Industry Press , Beijing2006) [5] WuShiKang: Polymer Photochemical Introduction-basis and Application (Science Press, Beijing 2003) [6] WeiXianFu WangNa jia NiPingXiu GuLing withdrawal of light snow adhesive and printing ink to offset oil impact on China printing ink rheology and packaging research in November 2010 (second edition) [7] FengChangYong influence printing ink transfer rate the analysis of the factors of henan mechanical and electrical engineering school journal in November 2008

Materials and Method The materials required in this study are silicon wafer, pattern transfer mask, aluminum wire, acetone, photoresist, photoresist developer, aluminum etchant and distilled water.
Leow, “Design and fabrication of Passive Fluid Driven Microchamber for Fast Reaction Assays in Nano lab-on-chip Domain,” Journal of Applied Sciences Research, vol. 8, no. 8, pp. 4254–4261, 2012

Fig. 1 Geometric model of driving axle housing Material of the body of the driving axle housing is 16MnL, elastic modulus , Poisson’s ratio , yield limit strength .
Material of the axis sleeve is 40Cr, elastic modulus , Poisson’s ratio , yield limit strength .
There is a maximum stress around the spring seat, the stress value is 288.9MPa, which is less than yield limit strength of the axis sleeve material of 670MPa.
Although the stress value meets the strength requirements of material, the stress concentration region is around welding seam between the axis sleeve and the flange.
Li: Journal of Jishou University (Natural Science Edition), Vol. 30 (2009) No. 3, pp. 80-82 (in Chinese)

Cracking moment test program for the BFRP-strengthened RC beams Material properties.
The rebar used in the test is HPB235, the design strength grade of concrete is C20,C30,C40, the fiber reinforced composites used are BFRP and CFRP, the measured mechanical property index of various materials, are shown in table 1, table 2 and table 3.
Early load progressively increase by 10% of Pu (Pu is the estimated value of the ultimate load for the test beam, which is obtained by the material measured mechanical property index).With the approach of cracking load, progressively increase the load by 5% of Pu, and make an observation during the sustaining load.
Journal of Zhengzhou University (Engineering Science) , Vol. 6(4) (2009),p.61-65(In Chinese) [5] Jianting Lin.

Acknowledgement It is a project supported by National Natural Science Foundation of China (Grant No. 51407063) and Doctor Scientific Research Foundation of Hubei University of Technology (Grant No.
[2] Rui Quan, Xinfeng Tang, Shuhai Quan, et al: Journal of Electronic Materials, Vol. 42(2013), p. 1469-1475
[3] Rui Quan, Xinfeng Tang, Shuhai Quan, et al: Advanced Materials Research.

Simulation on Current Efficiency of Electrolytic Cleaning for cold rolled strip Xiaokui Liu 1, a, Shuaifang Li1,b , Pengfei Gao1,c and Nan Qiao1,d 1 Faculty of Materials and Energy, Southwest University, Chongqing 400715, PRC axiaokui@swu.edu.cn, blshf860428@126.com, c raygaoswu@126.com, dqiaonan@swu.edu.cn Keywords: Simulation, Electrolytic cleaning, Cold rolled strip, Current efficiency Abstract.
Acknowledgement This work was financially supported by the Fundamental Research Funds for the Central Universities (XBJK2009B002) and the Chongqing Natural Science Foundation of China(CSTC,Grant No.2010BB 4128).
References [1] Tianliang Zheng: Chinese Journal of Aeronautics, vol.16(2003),p.123
[6] Pengfei Gao: Applied Mechanics and Materials,Vols. 44-47 (2011),p 2954.

Introduction Magnetorheological fluids (MRF) is a kind of smart material whose behavior can be regulated, it is a stable suspension formed from non-colloidal particles being dispersed into insulating carrier medium whose rheological behavior can be controlled by changing external magnetic field [1].
In this set-up, the crystal detector needs to satisfy square detection such that detection current can represent relative power; a galvanometer is used for measuring output power of reflection-type resonant cavity with its range 0~200 μA; the frequency of microwave is measured by direct-reading frequency meter; when measure microwave by crystal detector, in order to obtain higher detection efficiency, the detector is always equipped with an adjustable short-circuiting piston, adjusting its position can locate detector tube at the antinode of microwave, thus it should be noted to adjust its position when frequency is changed so as to make detector tube always located at that place; some medium or absorbing materials which can greatly absorb microwave energy are loaded into waveguide as matched load, it can almost absorb all the incident power; a container used for containing MRF is made up of plastic sheet (length 3.919cm, width 2.086cm, height 0.942cm, thickness 0.107cm).
Acknowledgement The authors are grateful for the financial support from natural science foundation of Hubei Province (No. 2007ABA086).
Kordonsky: Journal of Intelligent Material Systems and Structures Vol. 7 (1996), p. 123 [2] Jijun Fan, Xiaoping Zhao, Xiuming Gao, Changnian Cao: J.

Materials and Methods The source area of the Huihe River is situated at the eastern part of Shangqiu City, Henan Province.
Acknowledgements This work was financially supported by the National Social Science Fund (08BJY074); Anhui province Colleges and Universities Natural Science Research Project (KJ2012Z402); Anhui Province Science and Technology Project (11020503084); Scientific Platform Foundation of Anhui Engineering Research Center for Coal Exploration (2012YKF12).
Journal of Hydrology, 379: 284-290(2009)
Environmental Science,Vol.26(4): 3070-3075(2012)
Chinese Journal of Spectroscopy Laboratory,Vol.29(2): 912-916(2012)

Polymerase chain reaction denaturing gradient gel electrophoresis (PCR-DGGE) was used to analyze microbial characteristics to investigate the effects of operation conditions on microbial communities. 2 Materials and methods 2.1 Wastewater.
Environmental Science, 2007,28(3): 517-521
Journal of Shenyang Jianzhu University (Natural Science), 2009, 25(3): 544-547
Journal of Shenyang Jianzhu University (Natural Science), 2009, 25(3): 531-534
Beijing, China Environmental Science Press, 2002.

Wall and roof materials are assessed by heat preservation; the shape, length, width and layout of building plane are comprehensively designed.
The main key techniques of this stage are as follows: Control of Construction Materials Consumption.
Control of Construction Materials Reservation.
By reservation theory, reservation quantities of varied construction materials, e.g., steel, cements, sand, timbers, falseworks are optimized.
The new type heat preservation materials and dope of outside wall, the new type wall materials are employed to achieve energy-saving of buildings.