Search results

Planes et al. [13], on the other hand, suggested that fillers with a large interface influence degradation by trapping radicals that can react with intermediary chemical species implicated in matrix breakdown.
According to Tang et al., [16] formation of the compact charred layer is essential to provide an effective shield against mass and heat transfer.
El-Nemr, Effect of different curing systems on the mechanical and physico-chemical properties of acrylonitrile butadiene rubber vulcanizates, Mater.

The validation of the AEM numerical model has been made simulating in the ELS® computer software an experimental test performed by Yi et al. [13] on a planar RC frame.
A time removal of tr = 5 ms is used, and similar with Sasani et al. [18], Thai and Lin [5], the damping ratio is set to ξ = 5%.
El-Fouly and H.

However, Amblard et al. [10] have already pointed out that pH variations and the cathodic hydrogen co-deposition also determine the growth mode and the texture of electrodeposits.
According to Amblard et al. [10], the observed texture is a result of the plating conditions and of processes that occur in the cathodic layer.
El-Sherik U.S.

El Ali, C.
Al-Sharabi, R.
Al-Harthi, Effect of fluorine on the critical current density of thallium based high Tc superconductors, J.

Alloy 718 is a widely used Ni-base superalloy that is strengthened by γ'' (bct, Ni3Nb) precipitates. 718Plus is a new Ni-base superalloy recently introduced by ATI Allvac. 718Plus is strengthened primarily by γ' (fcc, Ni3(Al,Ti)) precipitates, but also contains some γ'' precipitates.
Composition of the alloys that were studied (Wt. %) Alloy Cr Al Ti Fe Nb Mo Co W C Ni 718 18.3 0.56 1.05 18.1 5.1 2.86 0.12 - 0.05 Balance Allvac 718Plus 18.32 1.4 0.84 9.45 6.29 2.87 9.82 1.29 0.02 Balance Samples from Alloy 718 and Allvac 718Plus with dimensions ∅6 mm х 9 mm and ∅8 mm х 12 mm were machined from hot-worked rods of 256 and 200 mm in diameter, respectively.
Mechanical properties of alloys 718 and Allvac 718Plus after SPD at room temperature Alloy Grain size, [µm] Ultimate Strength, [MPa] Yield Strength, [MPa] El, [%] RA, [%] 718 0.5 1699 (long.) 1438 5.4 6.4 [9] 718 0.1 1799 1696 1.7 6.1 Allvac 718Plus 0.25 2067 1826 1.3 4.7 Summary 1.

Du, J, Li, L, Gan, et al.: J.
Al-Oufy and M.
El-Messiry: Alexandria Eng.

Tang, et al.: Nonlinear Dynamics, Vol. 62 (2010) No.4, p.931
Doherty, et al., eds.
Beresford, and E.L.

Experimental procedure A 304L-type austenitic stainless steel, (Böhler A607: 0.03 % C, 0.75 % Si, 2.00 % Mn, 18.80 % Cr, 9.00 % Ni and balance Fe) as well as the nickel-based alloy 80a (Böhler L306: 0.06 % C, 19.50 % Cr, 2.40 % Ti, 1.60 % Al and balance Ni), all in wt%, with an initial grain size of about 20 µm for the alloy 304L and 30 µm for 80a superalloy were provided by Böhler Edelstahl GmbH, Kapfenberg, Austria.
El-Dasher, A.D.
Beaudoin et al, TMS, (2003), p. 3 [9] H.

Elements such as Al, Sn, and O are ⍺-stabilizer elements that can raise the ⍺ ® β-transus temperature (Tβ).
Jiguang et al., “Solution Treatment,” vol. 44, no. 9, pp. 1–4, 2019
Li et al., “Simultaneous strength-ductility enhancement in as-cast Ti6Al4V alloy by trace Ce,” Mater.
El-Hadad, and A.
Vasilescu et al., “Effect of thermo-mechanical processing on the corrosion resistance of Ti6Al4V alloys in biofluids,” Corros.

In order to test the suitability of developed materials for application in the construction of photovoltaic cells, a series of dye-sensitized solar cells ITO/TiO2/dye/active layer/Al were prepared.
Dobrzański, et.al., Graphene-based layers deposited on to flexible substrates: Used in dye-sensitized solar cells as counter electrodes, Appl Surf Sci. 424 (2017) 157-163
Al-Kahlout, ZnO nanoparticles and porous coatings for dye-sensitized solar cell application: Photoelectrochemical characterization, Thin Solid Films 520 (2012) 1814-1820
Al-Ghamdi, Zarah H.
Gafer, Farid El-Tantawy, F.