Search results

China 3 Chongqing Academy of Agricultural Sciences, Chongqing 401329, P.R.
Materials and Methods Fungal Isolates and Plant Materials.
Journal of General Microbiology 123(1981)377

Its characteristics are: has three distance mode for selection by jumper J1 (short range mode, mid-range, adjustable distance); l Short range mode: 10cm—80cm or so (depending on the surface of materials measured decision); l medium range mode: 80cm—400cm or so (depending on the surface of materials measured decision); l Adjustable range mode: Adjustable parameters determined by the scope.
[3] Sensors for distance Measurement and Their Applications in Automobiles [J] .Aalen Germany: University for Applied Sciences
Localization of an autonomous mobile robot based on ultrasonic sensory information .Journal of Intelligent and Robotic Sys-tems:Theory and Applications. 2001, 3(30) :267-277

In the present work, ferrite-cerium-manganese samples have been prepared via a simple precipitation method using Fe(NO3)3×9H2O, Mn(NO3)2 and Ce(NO3)3×6H2O as starting materials, and NaOH, NH4OH and Na2CO3 as precipitant agents.
Fe(NO3)3×9H2O, Mn(NO3)2 and Ce(NO3)3×6H2O were used as starting materials, and NaOH, NH4OH and Na2CO3 as precipitant agents.
Alam: The Arabian Journal for Science and Engineering.

Fabrication and Analysis of a Tunable Inductor Jianlin Liu1,a, Xianghong Li2,b, Binzhen Zhang3,c, Jian Zhang4,d， Changhong Ji5,e and Haitao Yao6,f 1,2,3,4,5,6Key Laboratory of Instrumentation Science & Dynamic Measurement (North University of China), Ministry of Education, Taiyuan, China aliujianlin1985@126.com, bpet.cdy@163.com, czhangbinzhen@nuc.edu.cn, ddragson10@126.com, e4790-a@163.com,fyaohaitao.1986@163.com (Binzhen Zhang) Keywords: Radio Frequency, Inductor, Quality Factor (Q), SU-8 Abstract.
Design In order to decrease the skin effect loss at high frequency, it is necessary to use low resistivity metal materials to form the conductor.
In our work, we choose low resistivity material, for example, copper as the conductor.
Therefore, if the material, size and working frequency of mental coils are known, the total impedance can be calculated, just as follows: = Re（） (9) High frequency signal delivered in inductor will produce vortex induced electric field in mental wires.
[7] Tao Wang, Yong Wang, the optimization of the spiral inductor based on binarysearch method, Chinese journal of semiconductor, Vol.24, No.9, 2003.

Dynamic membrane bioreactor is a new type of wastewater treatment technology, which uses the coarse mesh material (such as non-woven fabric, wire mesh, etc.) as the filter base material.
Materials and methods Emulsified oil wastewater.
Environmental Science and Technology, 40: 2706–2713
Journal of Biological Chemistry, 193(1): 265–275

Introduction B4C is a well-known ceramic, as one of the hardest materials with high elastic modulus, high melting point and low specific gravity.
Wang: Journal of CSIMM.
Kim: J. of Materials Science.

Numerical Modeling of Planar Flow Casting Process Kee-Hyeon Cho 1,a, Kee-Ahn Lee 2,b, Moon-Chul Kim 1,c and Joong-Mook Yoon 3,d 1 RIST (Research Institute of Industrial Science & Technology), Gyeongbuk 790-600, Korea 2 School of Advanced Materials Engineering, Andong National Univ., Gyeongbuk 760-749, Korea 3 AnyCasting Co., Ltd., Seoul 157-842, Korea a khcho@rist.re.kr, bkeeahn@andong.ac.kr, cmckim@rist.re.kr, and djmyoon@anycasting.com Keywords: PFC (Planar Flow Casting), Amorphous Strip, Rapid Solidification, Puddle Abstract.
Still, the heat transfer phenomena of the single-roll process are complicated by the accompanying phase changes of the moving solid/liquid interface as well as the flow of the material in both liquid and solid phases [3,4].
- All material properties are constant and isentropic
CHANG and CHENG-I, WENG: Numerical Modeling of Twin-Roll Casting by the Coupled Fluid Flow and Heat Transfer Model, International Journal for Numerical Methods in Engineering Vol.40 (1997), p. 493 [4] Pryds N.

Journal Citation (to be inserted by the publisher ) Copyright by Trans Tech Publications Obtention of Silicate-Substituted Calcium Deficient Hydroxyapatite by Dry Mechanosynthesis C.
Materials and Methods Two mechanochemical reactions were performed in a planetary Retsch mill, milling at 350 rpm.
Acknowledgements The authors thank the Science and Technology Spanish Ministry for funding this work through the Integrated Action HF00-97.
Bonfield: Key Engineering Materials Vols. 218-220 (2002) pp. 203-206 [2] I.R.

In practice of engineering, the cracks are often found near the inclusion when the forces applied to the composite materials containing inclusion.
As a result, it is important to study this problem especially for non-destructive inspection and strength designing of the composite materials.
Acknowledgements National Natural Science Foundation of Heilongjiang Province (A0206) References� [1] Pao Y.
Journal of Harbin Engineering University.Vol. 25(2004), p. 618-622 [4] Liu Diankui, Lin Hong.

Introduction There are complex components of pollution material, poor biodegradability in straw pulp papermaking wastewater.
From Fig.1 and Fig.2 showed, there were irremoved material which were phthalic acid mono-2-ethylhexyl ester and Diisobutyl phthalate (DIBP). 1.
According to the characteristics, it used absorption intensity of wastewater at the 254nm wavelength to reflect the number of aromatic substances, and to indirectly reflect the removal rate of material difficult to be biodegraded by the combination process.
References [1] T.X Li: Study on the Preparation and Mechanism of A New Kind of Mesoporous Water Purification Material (Ph.D., University of Science and Technology Beijing, China 2005), P.8
Abdelwahab: Chemical Engineering Journal, Vol 146 (2009), p.205