Search results

Experimental Materials and specimens.
Materials Science and Engineering A, 213 (1996): 134-137
Materials Science and Engineering C, 26 (2006): 1269-1277
Materials Science and Engineering A, 527 (2010): 6193-6199
International Journal of Fatigue, 29 (2007): 843-851

Experimental Materials.
Influence of the additive amounts of reactive materials.
Besides, with the advance of modern science and technology and the innovation of electronics, a large amount of waste containing BFRs, such as waste printed circuit board and non-metal materials, waste TV plastic shells and polyurethane foam from waste refrigerators will be generated.
Thus, this study will also give a reference to the dehalogenation of these materials.
Yuan, Visible light-driven degradation of tetrabromobisphenol A over heterostructured Ag/Bi5Nb3O15 materials, RSC Adv. 2 (2012) 4656-4663

During electron beam penetrating materials, the peak PD of heat source is increased progressively as the effective radius of focused electron beam decreases in depth direction.
The materials used in welding experiments are magnesium alloy AZ61.
The peak temperature of weld bottom is high to about 600°C, which is higher than the melting point of materials.
Although the materials on the weld bottom are molten, the metal vapor plasma with high temperature is spouted out of the top-surface of weld to form a larger weld opening.
Le Masson: International Journal of Thermal Science Vol. 46 (2007), p.128-138

Liquid carbon dioxide purification system, including liquid purification tank cylinder, liquid purification cylinder exhaust valve, the liquid purification tank outlet valve, temperature sensors, pressure sensors, level detectors, valve switch controller, thermal insulation materials.
Of course, we include the central control system (including a variety of sensors, detectors, controller and its connection material), insulation materials and other facilities.
Fund Project: Science and technology development plan of Shandong province (2011YD08004) References [1] G.T.Rochelle, Amine Scrubbing for CO2 Capture, Science.325(2009),16-52
Journal of Geophysical Research 92:D5, 5497–5504

Introduction Biochar, a carbonaceous material, is produced from biomass in a closed unit with little or no available air at relatively low temperatures (< 700 °C).
Joseph, Biochar for environmental management: science and technology London: Earthscan,2009
An experimental investigation into the formation of polycyclic-aromatic hydrocarbons (PAH) from pyrolysis of biomass materials.
International Journal of Energy Research (2007)
[19] Thomas Mc Grath, Ramesh Sharma, Mohammad Hajaligol .An experimental investigation into the formation of polycyclic-aromatic hydrocarbons (PAH) from pyrolysis of biomass materials.

When the temperature stress is larger than tensile strength of concrete material, it may cause cracks which influence beauty and durability of bridge.
Because the main tower of bridge is hollow reinforced concrete tubular structure, its heat transfer properties of concrete material and the bridge tower’s wall is thick.
Acknowledgements This work was financially supported by Beijing Higher Institution Engineering Research Center of Structural Engineering and New Materials, BUCEA.
Journal of China Three Gorges University, China 2007, No.4 (In Chinese) [4] C.X.
Zhou: Design, Analysis of Cracks Appeared in Concrete Box Girder and Research of Repair Measures Research about Baishazhou Bridge (MS., Huazhong University of Science and Technology, China 2008).

Application Study on the Steel Fiber Reinforced Concrete Wen Cui1, a, Qin Luo 2, b 1 Department of Civil Engineering Luoyang Institute of Science and Technology，Luoyang Henan China, 471023 ajanecui9@163.com, bluoqin91@163.com Keywords: Steel fiber reinforced concrete; mix design; tensile strength ; compressive strength; construction technology; mix; pour; vibrate; cure Abstract.
Its primary purpose is according to the requirement to reasonably determine four basic parameters which include the water-cement ratio of the mixing materials, steel fiber volume ratio, the unit water and sand rate, and then the amount of the constituent materials was calculated.
It was necessary to pay attention to several problems, which include that preventing the agglomeration of steel fiber or broken, a mixing quantity should not be greater than 80% of the rated mixing quantity in order to avoid the mixer to stop working for overload, preventing the material mouth jam.
Peng, Theory and Design of Modern Concrete, edtied by Wuhan University of Science and Technology Press, May.2002, In Chinese
Ren, in: Haihe river university journal, Jan.2006, P. 92, In Chinese.

Introduction The Principal Component Analysis (PCA) technique emerged in 1901, but it was applied to the most diverse areas of science in 1993 [4].
Materials and Methods The study was conducted with 12 companies from the city of Curitiba and metropolitan region, contacted through the Association of Electro-electronic Industries [1], and based on interest in the theme.
The companies manufacture power meters, household appliances, computers, electrical material, circuit breakers, switches, among others.
Journal of Animal Science, v.66, n.9, p.2147-2158, 1988
Applied Mechanics and Materials, v. 518, p. 329-334, 2014.

The height-diameter ratio of all specimens is 3:1, and the tubes are coiling welded by Q345 steel material and filled with C40 concrete.
FE model simulations Constitutive model of materials.
The material grade of the steel tube is Q345 which belongs to low-carbon steel.
[3] Han Linhai: Structures of Concrete-filled Steel Tube Columns (Science Press, Beijing 2007)
Providence, R.I.: ABAQUS Inc. (2004) [10] Huang Chao, Han Xiaolei, Ji Jing: Journal of Building Structures.

., Shenyang Institute of Aeronautical Engineering, Shenyang, 110136, China 2 College of Materials & Metallurgy, Northeastern University, Shenyang, 110006, China 3 Dept. of Mat.
Sci., Graduate School of Engineering, Tohoku University, Sendai, 980-8579, Japan a wangjijie02@yahoo.com, b ydwang@mail.neu.edu.cn, cishida@material.tohoku.ac.jp Keywords: Two-way shape memory effect.
Acknowledgements This work is supported by a Grant-in-Aid for Science Research and Development from the Ministry of Education, Science, Sports and Culture of Japan, also the National Key Natural Foundation of China under grant No. 50531020 and the Special Aeronautical Foundation of Liaoning Province, No.2005400607.
Wayman: Shape Memory Materials.
Ishida: Journal De Physiqueiv, 5(1995),C8-961