Search results

Topography experiments were carried out at the Stony Brook Synchrotron Topography Facility, Beamline X-19C, at the NSLS, BNL (DOE Office of Basic Energy Sciences Contract no.
Blakeslee, Journal of Crystal Growth 27, 118 (1974)
Rumyantsev, “ Silicon carbide,” in Properties of Advanced Semiconductor Materials: GaN, AlN, InN, BN, SiC, SiGe, edited by M.
Tsuchida, Materials Science Forum 717-720, 313 (2012).

Thus to install some sound-absorbing porous material along the inner wall will surly enhance the muffler’s silencing performance.
Thus to add the sound-absorbing porous material on the inner wall, which can improve the muffler’s silencing performance.
Experimental Thermal and Fluid Science, 68 (2015) 468-483
Journal of Wind Engineering and Industrial Aerodynamics, 143 (2015) 34-41
Experimental Thermal and Fluid Science, 68 (2015) 468-483

Introduction As the increasingly requirement of lightweight in modern traffic , 3C production and aerospace, human environmental awareness is gradually strengthened, magnesium alloy with high performance and equitable price was pressed for in the market, therefore, huge material and human resources are invest in developing new magnesium alloy material and new processing technology with short-flow and low-cost in many developed countries[1].
Materials and experiment method Test flow is shown in Fig.1.
Acknowledgements The authors would like to thank the sponsor of the National Natural Science Foundation of China(NSFC, Sponsor NO.50674017 and 50804023) and sponsor of the Science and Technology Project of Jiangxi Office of Education(NO.
Journal of Japanese Institute of Light Metals ,2001 ,51(1) :2 - 13

Introduction Phthalic acid esters (PAEs), also known as phthalates, are lipophilic compounds commonly used in the polymer industry to increase flexibility [1] (e.g. plastic films, insulating and covering materials, toys, medical devices).PAEs are produced worldwide at up to several million tons per years and are among the most abundant contaminants in the environment and food.
Materials and methods Sampling sites.
Acknowledgements This work was supported by Major State Basic Research Development Program of China (973 Project NO. 2011CB100400), Science and Technology Planning Project of Guangdong Province, China (Project NO. 2012A0201000003) and Agricultural Science and Technology Project of Guangdong Province, China (2011NO.584).
Chi, Journal of Soils and Sediments 2012, 12, 1189

Emekeev, Applied Mechanics and Materials. 756 (2015) 633–639
Charikov, Key Engineering Materials. 685 (2016) 816–822
Shulaeva, Indian Journal of Science and Technology. 8 (2015) 1–8
Conf. on Control Problems ARCCP-2014 (Moscow: The V A Trapeznikov Institute of Control Sciences), 2014.

Igumenov1,d 1 Nikolaev Institute of Inorganic Chemistry, Siberian Branch, Russian Academy of Sciences, Novosibirsk, 630090, Russia 2 Boreskov Institute of Catalysis, Siberian Branch, Russian Academy of Sciences, Novosibirsk, 630090, Russia a email: maxpol@niic.nsc.ru b email: trend@niic.nsc.ru c email: vvk@catalysis.ru d email: igumen@niic.nsc.ru Keywords: thin coatings, technological device equipment, nano-sized layers, copper films, nanotechnology, metal layer deposition Abstract.
Introduction New physicochemical methods developed for the deposition of nanodimensional metal structures on solid substrates offer a basis for the future progress in microelectronic technology, heterogeneous catalysis, synthesis of novel optoelectronic materials, etc. [1–6].
Igumenov: submitted to Journal of Inorganic Materials (2012)

With reference to the geologic report and test data, parameters of DP material cohesion angle C1, internal friction angle C2, expansion angle C3 and elastic modulus are set on detailed test data and engineering experience.
The maximum Von-Mises stress is almost reaching the yielding stress of the material with 350Mpa.
Acknowledgements The work is financially supported by the national natural science foundation of China (No.51309209), (No.51279186), (No.51279188).
Sun, Bearing Capacity Analysis of the Slab of Slipways at Marine Engineering Construction Site [J], Advanced Materials Research. 1051(2014) 715-720 [4] George Brink, J.
Louis van Rooy, The influence of the geological origin on soil volume change through collapse settlement [J], Journal of African Earth Sciences 101 (2015) 113-118 [5] Z.

A possible octadecane source is from the sealing materials of the clean room ceiling, but it has not been determined yet.
Gentile, Applied Surface Science, 225, p. 256 (2004)
Ohmi, Japanese Journal of Applied Physics, 30 'o. 3B, p.
Harazono, Materials Science and Engineering B, 4, p. 401 (1989)

Research and Application on the Urban Public Transport Route Accounting System Zhike Han1, a, Quan Pan1,b and Bowen Yang2,c 1 College of Computer Science Zhejiang University City College ,Hangzhou China 2 Computer Science and Technology College of Zhejiang University, Hangzhou China ahanzk@zucc.edu.cn, bpan.quan.zu@gmail.com, cybw_zju@126.com Keywords: bus route accounting; public transport; cost sharing Abstract.
Cycling is an important project accounting is accounting for warranty costs, maintenance and minor repairs categories of diversity of the frequent maintenance expenses of management as weak, with real-time settlement system, strengthening the process of consumption Bus maintenance control, improve material consumption transparency, the main question of the contract specifications settlement relationship, with clear, repair both sides Zequan Li, reflecting the cost and value of consistency, to eliminate the occurrence of waste, materials, fixed by changing the existing settlement pattern, each maintenance operation project must be confirmed both mechanic and pilot, and description section of the distribution system reform, the pilot of the pilot material savings incentives, and the material has been effectively monitored, making financial accounting segment, management processes and further transformation.
Mill Valley, CA: University Science, 1989
[8] Electronic Publication: Digital Object Identifiers (DOIs):Article in a journal: [9] D.
Rakic, “Cell Proliferation without Neurogenesis in Adult Primate Neocortex,” Science, vol. 294, Dec. 2001, pp. 2127-2130, doi:10.1126/science.1065467.Article in a conference proceedings: [10] H.

Carbon fiber-reinforced plastics (CFRP) are typical difficult-to-machine materials, which is easy to produce many defects such as burrs, dilacerations, layering in milling process.
Diamond coating is a kind of superhard multifunctional material.
It has become the best idea material for special cutter of machining CFRP[5].
But the fiber layer is difficult to completely cut off at the upper surface of material, due to lacking the support of material.
Deger: International Journal of Machine Tools & Manufacture, (2012), No.5, pp. 79-93