Search results

Introduction Advanced composite materials, like carbon fiber reinforced plastics (CFRP), stand out for their excellent characteristics such as lightness, high strength and high corrosion resistance.
The carbon fiber material [5] used is shown below
Future studies in this field will have to be multifaceted investigations of materials, structural and other matters related to durability evaluation.
Ackowledgements This study was supported by Grants-in-Aid for Scientific Research in 2010 from the Ministry of Education, Culture, Sports, Science and Technology of Japan.
[7]T.Hojo and K.Asao, Durability Evaluation of Carbon Fiber Reinforced Member, Proc. of IABSE Symposium (2008） [8] T.Hojo, S.Yokoyama and K.Asao, Durability Evaluation of Wooden Member Reinforced by Carbon-Fiber, Journal of Material Life Society,Vol.24,No.2 (2012) [9] Japan Conservation Project, Test Report on Reinforcement Effect of Carbon Fiber Using TORAYCA Laminate Method (2005）

Introduction Research on nano-crystalline materials has attracted much attention in recent years due to its unique properties.
The nano-crystalline materials often used in the fabrication of solar cells, light emitting diode, photocatalytic and many more.
The exciton properties of copper halogenide materials are greater than those of the materials belonging to the III-V and II-VI semiconductors.
The electrical properties of semiconductor materials are highly affected by the doping process.
Wijayantha, Deposition of thin conducting films of CuI on glass, Solar Energy Materials and Solar Cells 55 (1998) 283-289

Using Pro/E establish the solid model of oil-stone and oil-stone pedestal , then import the model into Ansysworkbench, according to the design requirements, oil-stone materials are SiC and Diamond, the material of oil-stone pedestal is 40Cr,the detail information see table 1.
So, using the higher hardness of oil-stone materials can decrease oil-stone's deformation and abrasion; self-driving ability of the higher hardness oilstone is not well. this will decrease honing quality of workpiece .
Taking honing quality and honing efficiency into consideration, during rough honing process, using the higher oil-stone materials, these kinds of oil-stone have follow characters :low abrasion, long serving life, could endure the higher speed and honing pressure ; during finish honing process, using common oil-stone materials, these kinds of oil-stone have good self-driving ability ,to make sure honing quality of workpiece surface.
[3] Yundian Zhang: Modern honing technology, Science Press (2007).
Mathiac, Journal of Materials Processing Technology 209 (2009) p.6078 - 6086 [8] Hailing Chen, in: Experimental studies on heavy honing technique, Jinan, Master thesis of Jinan University (2006).

Manganese is contained in the form of islands uniformly dispersed large mass of the base material.
Silicon is insignificant and appears only as an alloying element to the base material.
From the analysis of samples by electron microscopy SEM shows that if the heat treatment of pearlite grains are coarse classic uniformly distributed in the ferrite matrix therefore blade materials mechanical properties are reduced, the song has a good running, low durability and low mechanical strength.
Amjed, Thermal analysis of cooling effect on gas turbine blade, International Journal of Research in Engineering and Technology. 3, 3 (2014) 603-610
Trzaska, Calculation of the steel hardness after continuous cooling, Archives of Materials Science and Enginering. 61, 2 (2013) 87-92

The materials of the up and down inclined blades in the five-segment arch system were relatively small and also different in length.
The materials used in the plain wood of tri-segment arch and five-segment arch were great, and also the head and tail of wood materials were overlapped.
Sichuan Building Science, 2011, 37 (4): 104~107
Journal of Fuzhou University (Natural Science Edition), 2011. 39 (6): 917~921
Building Science, 2012. 28 (1): 108~110

Age-hardening of rheo-high pressure die cast Al-alloy 6066 TAUTE Carlien1,a *, MÖLLER Heinrich2, b 1Department of Materials Science and Metallurgical Engineering, University of Pretoria, Pretoria, 0001, South Africa 2Council for Scientific and Industrial Research (CSIR), Pretoria, 0001, South Africa aaurora247@hotmail.com, bhmoller@csir.co.za Keywords: rheo-high pressure die casting (R-HPDC), alloy 6066, age-hardening, solution heat treatment, Vickers Hardness.
Acknowledgements The Department of Science and Technology (DST) in South Africa is acknowledged for funding under the Advanced Metals Initiative Program.
Turkish Journal of Engineering and Environmental Sciences 31 (2006) 53-60
Materials Science Forum 794-796 (2014) 137-142
Materials and Manufacturing-Casting.

Experimental Program and Methods Material: The material selected for this investigation is an aluminium alloy AA7075-T7351 plate of 6.35 mm (0.25 inch) thickness, used extensively in the manufacture of typical airframe structures.
Grandt, Jr., Fracture mechanics consideration of residual stresses introduced by cold working fastener holes, Journal of Engineering Materials and Technology, 102 (1980) pp. 85-91
Reid, Aging aircraft repair strategies utilizing cold expansion technologies – Part 1, The science of cold expansion, PowerPoint presentation, Ageing Aircraft User’s Forum, 23-25 May, 2007, Brisbane, Australia
Schijve, Fatigue of Structures and Materials, Second Edition with CD-ROM, Springer Science + Business Media, B.
Clark, Modelling residual stresses and fatigue crack growth at cold expanded fastener holes, Fatigue and Fracture of Engineering Materials and Structures, 14. 5 (1991), pp. 575-581

Applying advanced research methods based on metallurgical sciences allowed us to conclude on a raw materials used for production of the investigated objects.
The work has been implemented within the framework of statutory research of AGH University of Science and Technology, contract No 11.11.170.318 - 11 AGH.
Aschenbrenner, The Occurence of Metallic Iron in Ancient Copper, Journal of Field Archaeology 2/3 (1975) 251-266
Kacprzak (Eds.), Binary Alloy Phase Diagrams, ASM International, Materials Park, Ohio, 1990
Kruszyński (Eds.), Ancient Caucasian and Related Material in The British Museum, The British Museum Press, London, 2002, pp. 87-98

The quality of road pavement depends on the materials used.
Modified asphalt can be produced using waste materials or by adding additives to the mixture [6].
Utilizing waste materials as additives in asphalt mixtures can also be a solution to reduce waste.
The waste materials in question include used outer tire waste and LDPE plastic waste [9].
Modified asphalt is a combination of several substitute materials, including used outer tires, LDPE, gilsonite, and Pen 60/70.

Material and methods Sampling.
Environmental Science & Technology Vol. 29 (2006), p. 50-53.
Journal of Oil and Gas Technology Vol. 29 (2007), p. 66-69.
International Journal of Coal Geology Vol. 76 (2008), p. 76-85
Environmental Science & Technology Vol. 34(2011), p. 25-30.