Search results

The materials were examined using SEM imaging.
Koenders: Effect of exposure on self healing behavior of strain hardening cementitious composites incorporating various cementitious materials, Construction and Building Materials, 42 (2013), pp. 217–224
Construction and Building Materials, 68 (2014), pp. 535–551
De Belie: Self-healing in Cementitious Materials - A Review. 
Materials, 6 (2013), ISSN: 1996-1944, pp. 2182–2217, online: http://www.mdpi.com/1996-1944/6/6/2182

Experimental Materials.
New Building Materials, 2007(5): 1-4(In Chinese)
Development of new gypsum cementations materials, Jiangsu Building Materials, 2006(03): 20-22(In Chinese)
Construction and Building Materials 27 (2012) 531–533
Journal of Guangxi University(Natural Science Edition), 2007(3): 26-30 (In Chinese)

It was found in recent years that the influence of DSA phenomenon, which always appears during the plastic deformation process of metallic materials under certain temperature and strain rates, on the mechanical behavior of materials should not be ignored [5-8].
Nuclear Materials Vol. 300 (2002), p. 178 [6] F.
Nuclear Materials Vol. 252 (1998), p. 257 [11] A.F.
Nuclear Materials Vol. 226 (1995), p. 216 [13] K.W.
Nuclear Materials Vol. 295 (2001), p. 21 [14] C.S.

All the elaboration processes (forming and finishing) of the metallic pieces introduce a set of stresses in the materials.
In some cases its level can be similar to the yield stresses of the materials.
X-Ray Diffraction technique is widely applied for residual stresses measurements in metallic materials (ICRS2 1989, ICRS3 1991and S.
The diffraction phenomenon must be understood under quantum mechanics science explanation far the objectives of this paper.
Int, Journal on Fatigue

Such construction can actually prevent penetration of vaporous moisture from a room into an insulation material.
It has been specified that only materials with water vapor permeability resistance not less then 12 [m2·h·Pa/mg] must be applied as water-vapor insulation layer.
Water vapor barriers using materials with water vapor permeability resistance not less than 12 [m2·h·Pa/mg] should be considered when making internal insulation for exterior brick walls.
Typical disadvantages of external insulation of buildings polystyrene (2007) Building Materials, 6, pp. 24 – 31
Features of energy efficient upgrade of historic buildings (illustrated with the example of Saint-Petersburg) (2014) Journal of Applied Engineering Science, Vol. 12 (1), pp. 1-10

Fig.1 Integrated architecture of production process ERP realizes enterprise administration function; It also coordinates the information interchanges between departments on manufacturing management, marketing management, materials supply management, etc.
Its task is defined according to that the production plan should balance the raw materials demand and the existing resources.
Marketing management system Plan management system Quality management system Equipment management system Materials provision management system Finecial management system Measure management system Contract of production arrangment Following contract Every day producti on plan Inform ation of fulfillin g plan Consume of auxiliary materials and energy Person and team information Stock wolume and shifting amount Labor cost Expended and depreciation cost of spare parts Parameter, actural operation, maintainable plan for equipment Checking materials Coming materials Result for new materials check Result for product objection Send back goods Stock end carrying for finished product Cost budget Measurement for waste Measurement for materials in process New materials measure Finished product measure Labor and capital management system Quality cost(wasters) Materials
Acknowledgement This research was supported by the National Natural Science Foundation, China (No. 70572098).
Hangos: Journal of Proceeding Cont Vol. 8(4)(1998),p.251 [3] H.H.

It has been well known that the metallic materials have the positive TCR property, whereas the semiconductor materials have negative TCR property.
On the other hand, for the semiconductor heater materials (SiC) it raised slowly in the low temperature region because of the high resistance of the materials.
To make an easy control of the temperature during the semiconductor thermal processing, we attempt to minimize TCR of the heating materials by mixing the semiconductor and metallic materials.
Kasap, Principles of Electronic Materials and Devices, 2nd ed., McGraw-Hill, New York 118, 2002
Yoshida, Japanese Journal of Applied Physics, 29, 7 (1990) L1175

Polymer materials flowing through the Die-plate are extruded from die-hole to cooling water, and then are cut into pellets by rotation knives.
In this process, the temperature uniformity of Die-plate can affect the flow rate uniformity of polymer materials directly.
The physical properties of materials Material Density [kg/m³] Specific heat [j/(kg·k)] Coefficient of heat conductivity [w/(m·k)] Die-plate 8030 502.48 16.27 Hot oil 830 2504 0.8 PP K7760 770 2300 0.2416 Pelletization Quality Assessment.
De A, The influence of ECAP die channel geometry on shear strain and deformation uniformity, Materials Science Forum. 584-586 PART 1(2008)145-150
[2] Shixiong Ren, Tao Lu, Shasha Dang, Kuisheng Wang, Numerical simulation of temperature field of die for polypropylene pelletizing under water, Journal of Mechanical Engineering/Jixie Gongcheng Xuebao. 7(2009)274-277, In Chinese

The addition of kinetic energy may be needed to move material from one point to the next or to agitate the material.
In rotating equipment solids, liquids or other materials shift through a mechanism of drivers like engines, turbines, motors, driven elements like pumps, compressors transmission elements and auxiliary equipments [2].
Laura-Diana, "qualitative, semi-quantitative and, quantitative methods for risk assessment: case of the financial audit," Scientific Annals of the “Alexandru Ioan Cuza” University of Iasi: Economic Sciences Series, vol. 2009
Mannan, "Fuzzy risk matrix," Journal of hazardous materials, vol. 159, pp. 152-157, 2008
Lansdowne, "Risk matrix: an approach for identifying, assessing, and ranking program risks," Air Force Journal of Logistics, vol. 22, pp. 18-21, 1998

Introduction Nitrogen (N)，as a detrimental element in superalloys，is not easily removed even during vacuum induction melting (VIM), and usually is controlled by selecting raw materials for minimizing the N level [1].
For getting the virgin alloy, the purified raw materials were melted at a temperature of 15800C for 10min, and then cast into metal moulds in a vacuum of 0.01 Pa to get the virgin alloy bar stock with the weight of 130kg.
Tensile tests with a strain rate of 2×10-5 s-1 were conducted on an AG-5000A Tensile Machine at room temperature and on a DCX-25T Material Testing Machine at 9000C, respectively.
[10] Yuan Chao, Guo Jianting, Zang Zhixin, Lai Wanhui, Liu Yiming, and Li Hongliang, Effect of the revert recycle times on the microstructure and mechanical properties in a cast nickel-base superalloy K446, The Chinese Journal Nonferrous Metals. 16 (2006) 453-458
[12] Yuan Chao, Guo Jianting, Gusong Li, Lanzhang Zhou, Yunchao Ge, Wei Wang, Effect and control of nitrogen in cast superalloys, The Chinese Journal Nonferrous Metals. 21 (2011) 733-746