Search results

Yang1,f 1 School of Manufacturing Science and Engineering, Sichuan University, 610065,China 2 School of Computer Science, Cardiff University, U.K.
Engineering geometric models are often designed to have symmetries and other regularities.
In reverse engineering, B-rep models are created by fitting surfaces from point sets obtained by scanning an object using a 3D laser scanner.
However, this is about the same as the highest complexity of object constructed by current reverse engineering methods.
Dutta: J. of Systems Engineering, Vol. 6(1996), p. 98 [5] B.I.

The conference was carried out under financial support of the Far Eastern Federal University, the Russian Foundation for Basic Research as well as at informational support of the Institute of Electrical and Electronics Engineers (Russian (Far Eastern) Subsection of IEEE).
The conference participants submitted papers reflecting recent advances in the field of materials engineering and technologies for production and processing in the different areas of modern manufacturing.
The international program committee has selected some papers for publishing in the Materials Science Forum (Trans Tech Publications Ltd.).

Studied composite is based on the advanced silicate matrix consisted of cement and suitable addition modifying mineral additives.
Due to application of advanced blend system the hydration continues.
Zatloukal, Relation between parameters of plasters measured by non-destructive and destructive methods, Key Engineering Materials 677 (2016) 211-214
Konvalinka, Development of Mechanical Properties of Steel Fibers Reinforced High Strength Concrete, Advanced Materials Research, Vol. 1077, pp. 113-117, 2015
Gardner, Numerical simulation of the long-term behaviour of a self-healing concrete beam vs standard reinforced concrete, Engineering Structures 102 (2015) 176-188.

Shao 1 and W Xia 1 1 Guangdong Key Laboratory for Advanced Metallic Materials Processing, College of Mechanical Engineering, South China University of Technology, Guangzhou 510640, China a zxkang@scut.edu.cn Keywords: Functional nanofilm, Polymer plating, Direct joining, Acrylic rubber, Peel strength Abstract.
The joining processes of metals to engineering rubbers are commonly separated into the indirect curing way [1-3] and the direct curing way [4-7].
A novel method has been developed for direct joining of engineering plastics and rubbers to magnesium alloy and other metals [8-11].
Forum, Vol.419-422 (2003), pp.921
Forum, Vol.488-489 (2005), pp.661

Preface The International Conference on Geotechnical Engineering-Iraq (ICGE-Iraq 2020) was organized by the Iraqi Scientific Society for Soil Mechanics and Foundation Engineering (ISSSMFE) in cooperation with the Civil Engineering Department/University of Baghdad.
ICGE-Iraq 2020 is a forum to bring together scientists, researchers and industry professionals to discuss innovative ideas and diverse topics on the next generation of sustainable geotechnical and geoenvironmental engineering.
The book contains recent research studies in several themes of geotechnical engineering and sustainability.
Generally, the accepted papers are belonging to the main themes of ground improvement, laboratory and field testing, shallow and deep foundations, and advanced soil mechanics.
Also, the research themes of this book are extended to include some studies in construction management and structural engineering.

Chen2, a 1 College of Materials Science & Engineering, Shandong University of Science & Technology, 579 Qianwangang Road, Qingdao 266510, China 2 Advanced Manufacturing Technology Research Center, Chinese Academy of Machinery Science and Technology, 18 Xueqing Road, Beijing 100083, China a matscichen@hotmail.com Keywords: diffusion couple, solid state reaction, diffusion and stresses, periodic-layered structure, mixed control Abstract.
Greer: Defect & Diffusion Forum Vol. 129-130 (1996), p. 339 [5] Y.C.
Cserháti, J. van den Akker and F.J.J. van Loo: Defect & Diffusion Forum Vol. 129-130 (1996), p. 253

Preface Cross-Strait Engineering & Technologies and Ceeusro Association (CETCA) is an academic association whose members teach or research is in the field of Engineering & Technologies and Ceeusro.
A primary goal of the CETCA is to offer an international forum for researchers and practitioners in the field to exchange ideas and present original research work on the theory and applications of Functional Manufacturing Technologies and Ceeusro.
In 2008, the council in period of 2nd Academic Conference of The Cross-Strait Engineering & Technologies and Ceeusro (Taipei, Taiwan) made the decision that the 3rd Academic Conference would be held in winter of 2009 in Changzhou, and Changzhou Institute of Technology would be responsible for the preparation work .The aim of the Academic Conference is to exchange the information about the new theory, technology, method and equipment in the field of Engineering & Technologies, and to promote the integration of production, teaching and research in the world.
The major topics covered by the conference include Innovation and Experience in Engineering & Technology and Ceeusro; Material Science and Technology in Manufacturing System and Technologies, and Administrative Skill of Advanced Manufacturing and so on.
Professor Dunwen Zuo Chairman, the 3 rd International Conference of Engineering & Technologies and Ceeusro Conference organizers Changzhou Institution of Technology Heilongjiang Institute of Science and Technology National Chin-Yi University of Technology Nanjing University of Aeronautics & Astronautics

Consequently, we invite some prominent researchers in this field to contribute research and review papers on the advances in nanostructured materials processed by SPD to this special topic volume of Materials Science Forum.
Liao School of Aerospace, Mechanical and Mechatronic Engineering University of Sydney, Sydney, NSW2006, Australia xliao@usyd.edu.au Y.
Zhao 2Department of Chemical Engineering and Materials Science University of California, Davis, CA 95616, USA yhzhao@ucdavis.edu

Zeng 1,b 1 Department of Mechanical Engineering, Tsinghua University, 100084, China a fangg@tsinghua.edu.cn, bzengp@tsinghua.edu.cn Keywords: Orthogonal cutting, Finite element method, Tool, Chip formation Abstract.
The rake angles, 0°, 5°, 10°, 15° and 30° are used when Advances in Materials Manufacturing Science and Technology 18 the cutting edge radius is 0.3mm.
Palmer and P.L.B Oxley: Proceedings of International Mechanical Engineers Vol. 173 (1959), p. 623 [5] E.
Black: ASME J. of Manufacturing Science and Engineering Vol. 118 (1996), p. 11 [9] E.
Lin: ASME Journal of Engineering Materials and Technology Vol. 114 (1992), p. 218.

Dargush and Banerjee [6] studied the transient heat conduction analysis of engineering components by using an advanced boundary element method.
Huang : Advanced Materials Research Vol.148-149(2011), p. 103
Li : Materials Science Forum Vol.654-656(2010), p. 1565
Banerjee: International Journal for Numerical Methods in Engineering, Vol. 31(6)(1991), p. 1231
Journal of Materials Engineering and Performance. 2011, Doi: 10.1007/s11665-010-9819-6.