Search results

According to O’Brien et al. [14], iodine value was done to determine the amount of the double bond that still exists after the oxidation reaction.
[4] M., Ferrari, E.L.

Al Shamaa, S.
El-Hachem, E.

Several years later, Zhang et al suggest a one step method to prepare OAPS[3].
Element analyses The element C,H and N were analyzed using Vario EL III element analyzer. 2.3.5.

M. et al. the enzyme laccase has been used to degrade indigo dye in the dyeing process, as they are environmentally friendly enzymes and are able to degrade the dye vat at promising rates. [2] As for solid waste, it is the current model of textile production and clothing and its high consumption that leads to the formation of large amounts of textile waste, as only 20% of this waste, worldwide, is recycled or reused; while the remaining 80% is landfilled or incinerated.
Tecnología Para El Acabado De Tela Jean Usando Enzimas Lacasas: Una Revisión

Morovič, el al.: Effect of the friction and reduction angle on the accuracy of cold drawing steel tubes STL model based on FEM analysis, in: Research papers MTF STU Trnava, Vol.28 (2020), pp. 32-39

Thus, the ratio between power and speed is very low, minimising the cutting capacity of the water jet as described by Pahuja et al. [19,20].
D’Orazio, M. el Mehtedi, A.

Chemical compositions [in wt%] of the steels investigated Alloy C Cr Mo Ni V Al Si* Mn* En19 0.37 1.03 0.02 0.23 0.02 - 0.1-0.35 0.5-0.8 En41B 0.46 1.60 0.30 0.40 - 0.85 0.40 0.60 (S= 0.05% and P = 0.05% in each steels) * Specification only - no analysis obtained Nitriding was carried out in a horizontal tube furnace.
Mittemeijer at el. [21] suggested that at normal pressure there is a strong tendency for compound phases to decompose into Fe and N2 and that causes gaseous nitrogen precipitation.

Lenka Müller et al. [25] believed when the CO32- concentration is lower than 20 mmol/L, PO43- of HA will be substituted by CO32- to form CHA, otherwise it will be substituted by (OH)-.
El-Sherif: Electrochim Acta Vol. 54(2009), p. 7280 [4] Samar J.

Power conversion characteristics of the OPV wire and OPV fabric devices Photovoltaic Parameters Organic Photovoltaic wire Plain PV Fabric Twill Fabric 5 harness Sateen Fabric Pin, mW 31.0 131 128.1 127.5 Voc, V 0.31 1.10 1.10 1.10 Isc, mA 2.30 0.89 1.48 1.49 Jsc, mA/cm2 7.43 0.68 1.15 1.17 Vmax, V 0.17 0.59 0.51 0.55 Imax, mA 1.72 0.52 0.71 0.74 Jmax, mA/cm2 5.57 0.4 0.55 0.58 Pmax, mW 0.29 0.31 0.36 0.41 Efficiency, % 0.96 0.23 0.28 0.32 Fill Factor 0.41 0.31 0.22 0.25 From Table 4 we can see that the efficiency of organic photovoltaic wire is around 0.96% as compared to 3.0% for same fiber reported by Lee et al [5].
Lee at el reported 3.0% efficiency for freshly prepared organic photovoltaic wire, but the organic photovoltaic wire we tested is already 1 year old and though we put the organic photovoltaic wire in desiccators in order to protect them from varying environmental conditions, they still degraded fairly.

Using the a | b | g notation of Lawler et al. [14], where a denotes the machine environment, b the processing characteristics and g the objective to minimize, the scheduling problem above is denoted Pm|sjk|ΣwjTj.
Management Science, 33, 1035-1047. (1987) [14] E.L.