Search results

The simulation method is saving time and material, but it need to be validated by wind tunnel test to insure the veracity of results [2] [3].
Acknowledgement This work was financially supported by State Natural Sciences Fund (11102070), the Key Laboratory of Manufacture and Test Techniques for Automobile Parts (Chongqing University of Technology), Ministry of Education, and Innovation Foundation of Jilin University.
Marzio Piller，Enrico Nobile，J Thomas．DNS Study of Turbulent Transport at Low Prandtl Numbers in a Channel Flow[J]．Journal of Fluid Mechanics，2002：419-441 [8].

Introduction Some special material and equipments need to pack and tie on a movable truck for testing the survivability and operation performance or for packaging otimization.
Chen, Journal of Fuzhou University(Natural Science), Vol.35(2007). p.70-75

Dyeing kinetics of henna natural dyestuff on protein fabric Hong Li1,2 a, Defeng Zhao1 ,Rui liu2,b 1 Faculty of Chemical ,Environmental and Biological Science and Technology of Dalian Technology University, Dalian,Liaoning 116024, China 2 School of Textile and Material Engineering of Dalian Polytechnic University, Dalian ,Liaoning,116034, China alihong@dlpu.edu.cn , bwoliurui@126.com Keywords: henna natural dyestuff, dyeing, kinetics, protein fabrics Abstract.
References [1] L.Gao,Y.J.Wang and Z.C.Yang:JOURNAL OF QINGDAO UNIVERSITY Vol. 19(2009), P. 37 [3] T.Liu and L.C.Jia:Wool Textile Jounal Vol.37(2009),p.24 [3] Al-Swhaibani Hamad: Materialwiss Werkstofftech Vol.12(2009),P.1060 [4] S.Y.Sui,P.Zhu ,C.H Xu and B.Wang: printing and dyeing Vol.10(2006)P.11 [5] S.Y.Sui,J.Guo and P.Zhu: printing and dyeing Vol.10(2009)P.13

It is sponsored by the National Science Foundation (NSF), under the leading of Pacific Earthquake Engineering Research Center (PEER), developed by UC Berkely and other American Universities.
Steel 02 is used to construct a uniaxial Giuffre-Menegotto-Pinto steel material object with isotropic strain hardening. [3] As shown in Fig 5 Steel 02 is used in this study.
Journal of Structural Engineering, Vol. 133, No. 1, January 2007, pp. 105-120 [3] Filippou, F.

The torsion force is given by (2) where w, l and t are the width, length, and thickness of the torsion beam, respectively, G is the shear modulus of the beam material.
Acknowledgements This work was supported in part by the National Natural Science Foundation of China under Grant No. 60278028 and No.61006075.
Journal of Semiconductors, 2010, 31(10): 106001

Fig. 2 The ultimate capacity of formwork support in all simulation conditions It can be seen from fig 2 that the bearing capacity of the vertical tube do not reach the theoretical calculation value of material strength in all tests.
[7] Caixia Chen, et al: Journal of Hunan Institute of Engineering (Natural Science Edition), 2006, 3: 024

A Vibration Data Acquisition System based on ICP Sensor and Cortex-M3 Siquan Hu1,a, Chundong She2,b and Hui Yao3,c 1School of Computer and Communication Engineering, University of Science and Technology Beijing, Beijing, 100083, China 2School of Electronic Engineering, Beijing University of Posts and Telecommunications, Beijing, 100876, China 3 Ruijie Networks Co., Ltd, Beijing, 100036, China ahusiquan@ustb.edu.cn, bscd@bupt.edu.cn, cyaohui@ruijie.com.cn Keywords: Vibration Monitoring; ICP Sensor; Cortex-M3; Data Acquisition System Abstract.
The sensor part of an ICP sensor contains a sensing element made of a piezoelectric material, which converts mechanical strain into an electrical signal; the IC part of the ICP sensor is an electronic circuit to amplify the sensor signal and transmit it to an external recording device.
Levinzon: IEEE Sensors Journal, Vol.12, No. 6, 2012, p. 2262 [6] ICP sensor on http://en.wikipedia.org/wiki/Integrated_circuit_piezoelectric_sensor [7] IEPE standard on http://www.mmf.de/pdf/an4e-iepe_accelerometers.pdf [8] Tiny Gecko on http://www.energymicro.com/

Thus it is evident that SnSe can be a better material for an absorber layer.
MohdZobir, Malaysian Journal of Analytical Sciences, 7 (1) (2001) 197.

Introduction of the Experiment Experimental Materials.
[3] Songyu Zhang, in:Study on Properties of Semi-rigid Steel Fiber Ceramic Concrete，Journal of Harbin Architectural Engineering College,1994,27(5):64-68 [4] Chengkui Huang. in: Fiber Reinforced Concrete Structures, China Architecture and Building Press(2004) [5] Xiuman Zhang, in: Experimental Research of Tensile Strength of Combined Aggregate Concrete, North China University of Technology, 2010.5 [6] The Ministry of Construction of China, Code for design of concrete structures(GB/T50081–2002)”, China Architecture and Building Press(2002)
[7] Danying Gao, Jianxiu Liu.: Theory of steel fiber reinforced concrete”, Science and Technology Press(1994).

Acknowledgement This work is supported by Natural Science Foundation of Guangdong Province in China (No.
Journal of Hazardous Materials, 140(2007): 280-292.