Search results

The building is made up of various materials.
Secondly, the science of house pattern design.
The selection of building materials and equipment Currently the utilization of low carbon building materials has already been developed to a certain extent, such as the use of green materials, the promotion of wall materials and products required by self-warm-keeping and the development of functional materials and composite materials.
Classified Dismantlement If construction materials cannot be classified before dismantlement, all kinds of materials are mixed up, and then, mixed wastes are produced.
Journal of Environmental Management,2009(9):2436~2447.

Igata: Key Engineering Materials.
Kawahara: Key Engineering Materials.
San Juan: Journal of Alloys and Compounds.
Ullakko: Smart Materials and Structures, Vol. 6 (1997), p. 616
Okanda: Science and Industry (ISSN: 0368-5918) (in Japanese).

The defect of blood bag could be a contamination of its raw materials.
The initial materials, such as chitosan, PVC, and glycerol was tested first.
To know the functional group of the synthesized materials and to prove that there was a new bond, the functional group characterization was performed as shown in Figure 2.
The addition of chitosan could decrease the hemolytic properties of materials with the increase of its concentration because it complemented the surface of PVC membrane [10].
Journal of Microbiology, 22(4)( 2004) [13] Palermo, E F.

Journal of the Structural Division, 98
Journal of Structural Engineering, 144, 04017199
Journal of Constructional Steel Research, 67, 1106-1114
Journal of Structural Engineering, 130, 895-903
Journal of Structural Engineering, 140, 04014083

Slag resistance is an integral characteristic of refractory products, it depends on the materials used, the structure and the manufacturing technology [4-7].
Literary Sources Review As a component that ensures low melt wettability, graphite and other carbon-containing materials, the content of which is up to 30% of the product mass, are widely used by developers of refractory materials [9, 10].
Sidorov, Studying of the slag-resistant corundum-graphite carbide-silicon-containing materials on the ethylsilicate bond, Refractories and technical ceramics. 6 (2008) 17-22
Shak, Investigation of the slag resistance of zircon-graphite refractory materials, Refractories and technical ceramics. 6 (2014) 39-44
Sidorov, Structure, oxidability, and thermo-mechanical properties of Al2O3-SiC-C materials on an ethyl-silicate bond, Refractories and technical ceramics. 11 (2007) 3-10

Demands for accurate information on the friction coefficient increased at the moment when manufacturers of stamping parts started to use simulation methods for prediction of sheet formability, also to apply new high-strength materials and materials with special surface treatments.
The friction coefficient f1,2 for experimental materials calculated according to Eq. (2) was f1,2 = 0.108 with R2 = 0.999 for DX54D and f1,2 = 0.131 with R2 = 1 for RAK 40/70 steel.
Exploring efficiency of tool coating via deep drawing of cylindrical cups, MM Science Journal 6 (2008) 20-23
[15] Schrek A., Švec P., Brusilová A., Gábrišová Z., Simulation process deep drawing of tailor welded blanks DP600 and BH220 materials in tool with elastic blankholder, Strojnicky Casopis, 68, (2018) 95-102
F., Influence of the plastic anisotropy modelling in the reverse deep drawing process simulation, Materials and Design 60 (2014), 368-379

Relevant studies were selected from a range of disciplines such as mechanical engineering, optics and laser technology, applied sciences, infrared physics, nuclear engineering, and lightweight material science.
However, they are less suitable for certain non-metallic materials [17][18].
Szwajka, And Et al. 2023 [11] 1.Materials and Their Characteristics.
Badoniya, “CO 2 Laser Cutting of Different Materials-A Review,” Int.
Sanghavi, “International Journal Of Engineering Sciences & Research Technology,” vol. 3, no. 4, pp. 1–5, 2014

Materials and Methods Two sets of SBR-OSA process systems were established.
Acknowledgements This work was supported by the Science & Research Program of Guangdong (Contract No. 2012A032300005, 2012B091000029), Science & Research developed Program of Foshan (Contract No. 2012HY100531, 2011BC100051) and Hong Kong and Guangdong key breakthrough projects in key areas (Contract No. 2012BZ100021) References [1] G.
Chen: Water Science & Technology Vol. 68 (2013), p. 530 [7] F.
Li: Journal of chemical technology and biotechnology Vol. 83 (2008), p. 109 [8] Y.
Muller: Water Science & Technology Vol. 56 (2007), p. 59 [12] L.

As a typical indirect dryer, paddle dryer has been utilized in many engineering fields to remove moisture of materials [24-25].
Yin: Coal Science and Technology Vol. 32 (2004), p.12 (in Chinese) [2] H.
Lü: CIESC Journal Vol. 62 (2011), p.2898 (in Chinese) [10] K.
Zhang, Nanjing University of Science and Technology (2013)
Cen: Chemical Engineering Science Vol. 64 (2009), p.5117 [25] H.

We then present a solution that maximizes the effective utilization rate of sheet material, for producing core columns of power transformers, and the passing rate of quality controls of matching coils and cores.
Engineering Journal.
Shenyang: Liaoning Science and Technology Press (1990)