Search results

Experimental Material.
Nakayama, M, Niwa, Relationship between the warm/cool feeling of fabric and the subjective evaluation of the quality of ladies’ knitted fabrics, International Journal of Clothing Science and Technology. 22(1) (2010) 7-15

The flow field grid was shown in Figure 2. 4.Boundary Conditions and Flow Field Calculation Set Based on mixture and model, considering the impact of acceleration of gravity, Grid model generated by Gambit was imported into solver of Fluent6.3, before calculation, material properties, the main phase and other phases of multiphase, boundary conditions and initial state, operating pressurewere set, and relevant physical parameters were also given in Table 1.
[3] Guannan Xi, Takeshi Ebisu, Kunikazu Torikoshi, “Difference in simulation with two and three-dimensinal, modals for finned tube heat exchanges,” Transport Phenomena in thermal science and progress Engineering, 1997,23(3), pp.755-760
[5] Chi-chuan Wang, Kuan-Yu Chi, Chun-Jung Chang, “ Heat transfer and friction characteristics of pain fin-and-tube exchanges,” International Journal of Heat and Mass Transfer, 2000, 43(15), pp.2681-2691

Humanized Design on Public Space of Underground Urban Complex of the Cold Cites Haiou Wang1, a, Xinbo YU1,b 1School of Architecture and Fine Art Design, University of Science and Technology Liaoning, Anshan, Liaoning, China,114051 a aswho@163.com，byxb-90@126.com Keywords: Humanized Design; Underground Urban Complex; Public Space; Cold City.
In attracting the shopping crowd, the population should be selected in the crowded position obviously, and as close as possible to the ground looks; set the transition region, the sink Plaza, grey space will connect underground space and ground space; join with markers of local context and active factors, such as sculpture, shops or billboards, enhance the population characteristics and attractive; wind and heat insulation partition as far as possible the use of light and transparent material, and the population is provided in the vicinity of artificial lighting, contrast with population space in good light, to attract people into the space.
References [1] Yang Cui, Peng Li, Xuan Wang. 2007, Chinese Journal of Underground Space and Engineering, 3(5) :787-791(In Chinese) [2] Wenqin Wang.

Introduction With the development of science and economy, automobile become one of the main means of transportation in people’s daily life.
InterdigitalDielectrometry Sensor Design and Parameter Estimation Algorithms for Non-Destructive Material Evaluation[D].
IEEE Sensors Journal, 2011, 11(6): 1440-1447

Table 1 Main parameters of gear shaper machines Main technical specifications YKS5132/YKD5132 Maximum diameter of workpiece (outer/inner) 320/220mm+Dcutter mm Maximum modulus 8 mm Maximum tooth width 90 mm Maximum length of cutter stroke 100 mm Rotary feed 0~2mm/str Radial feed 0~1000mm/min Relieving amount ≥0.3 mm Cutter shaft diameter 85 mm Shaft diameter 31.743 mm Diameter of working table 420/325mm Pore diameter of table 120/100mm 45 steel was cut as gear material, 32 cooling oil is used to cool the machine and it’s temperature is changed as 33℃, 40℃, and 47℃. 2.2 Test results and analysis Continuous cutting test was carried on for 15 times at each oil temperature.
Journal of Mechanical Engineering, 2013(21): 18-24
Engineering Sciences, 2013(01): 28-33

In order to improve the numerical results, more realistic material models that characterize the dynamic behavior of soil should be available.
Acknowledgements This work was financially supported by the Opening Foundation of Changjiang River Scientific Research Institute(CKWV2012307/KY), National Natural Science Foundation of China (51009055) and Basic Academic Program of Central University (2009B07514).
Journal of Hydraulic Engineering, Vol. 7(2001). p. 13-21

Experimental Commercial pure aluminium ingot with a purity of 99% was used as the matrix material, and it was reinforced with commercial Al2O3 and manganese particles.A stir casting setup consisting of a resistance furnace and a stirrer assembly was used for synthesizing the composites.
Acknowledgments The project is supported by the National Natural Science Foundation of China (Grant No. 50861008) and the Scientific Research Programmes of Colleges in Xinjiang (Grant No.
Wang: Journal of Natural Resource Vol. 5 (1990).p.311 [6] X.Y.

Tool Path Calculation based on the Actual Tool Profile Ping Zhao 1,2,a ,Wen Zhen Zhao1,3,b, Zhen Yun Duan1,c, Wen Hui Zhao1,d 1School of Mechanical Engineering, Shenyang University of Technology, No.111,shenliao road(south),shenyang economical&technological development Area, shenyang, China 2 Department of Mechanical and Engineering, Liaoning Province college of communication, NO.102,Shenbei Road, Shenbei New Area, Shenyang, China 3School of Mechanical Engineering, Liaoning Institute of Science and Technology, NO.176,Xianghuai Road,High-tech Industrial Development Area, Benxi, China a723725756@qq.com, b zhaowz1031@sina.com, c duanzhenyun@yahoo.com.cn, datuitoto@hotmail.com Keyword: Complex Curved Surface Machining; Tooling Path Calculation; Subpixel Precise Edge Extraction; Facet Model; Canny Algorithm; Minimal Orientation-distance Algorithm; NURBS Curve Fitting Abstract.
First we make the templet, the thickness of the templet is 5mm, and the material is hardened steel.
Vickers: Journal of Engineering for Industry, Vol. 115(1993), p.424 [3] J.

Ore-Proportioning Optimization Technology in Pellet Process Based on Self-characteristics of Iron Ores LV Xiaofang1, a, HAN hongliang2,b and HE Hongsheng3,c 1 Xingtai Polytechnic College, Hebei Xingtai, 054035, China 2 Institute of process Engineering, Chinese Academy of Sciences, Beijing, 100190, China 3 Xingtai Polytechnic College, Hebei Xingtai, 054035, China alvxiaofang000@126.com, bhlhan@home.ipe.ac.cn, c hhs-xt2008@163.com Key words: Iron ore power, Pellet, Self-characteristics, Optimizing ore-proportioning Abstract: The quality of pellet has a great extent effect on the BF smooth operation.
The importance and dominant characteristic of the developing for raw material preparation technology before iron making has gradually emerged especially for the modern blast furnace with improved equipment level and operation level[1,2].  
Vol. 40(2000), p.857 [6] S.WU, Y.LIU, J.DU: Journal of University of Sci. & Tech.

Application of Three-Dimension Visualization Technology in Water Supply Pipeline Information System Based on VTK Zhou Caiying1, a, Huang Longjun2,b 1JiangXi University of Science and Technology, Guangzhou 341000,China 2JiangXi Normal University, Nanchang 330022, China azhoucaiying_007@163.com (corresponding author), bhuanglong98614@163.com Keywords: three-dimension visualization; underground water supply pipes; management information system; VTK.
Introduction Underground water supply network is an indispensable component of urban infrastructure, and one of the major material foundations on which the city relies for its survival and development.
Journal of Geomatics,2006,31(1) [10] Schroeder WJ.VTK User’s Guide.