Search results

Currently, titanium base oxides are wildly used as the substrate materials, such as TiO2.
Raw materials costs are not only the key factors of producing biodiesel costs, but also the main factors that influence the cost of DME and F-T fuel.
Selecting appropriate alternative fuel and suitable raw materials considering local conditions are key issues in promotion and application for alternative fuels on marine engine emissions. 3.3 Integrated application of various technologies With the implement of IMO Tier III emission limits, different solutions should be taken at different stages to control NOx and SOx emissions.
Journal of Geophysical Research – Atmospheres, 2003, 108(20): 1-15
Application of selective catalytic reduction (SCR) on marine exhaust system [J].Science and Technology Consulting Herald, 2012, (2): 126-126

A significant difference in the interdiffusion coefficients of the gadolinium into UO2 and of the uranium into Gd2O3 causes a misbalance in material transport during the formation of the solid solution.
The authors also wish to express their sincere thanks to the staff of the Nuclear Materials Laboratory of the CTMSP for their assistance in the course of this study.
Dörr: Materials Science Monographs Vol. 16 (1983), p. 707
McCormick: Journal of Alloys and Compounds Vol. 281 (1998), p. 146
McCormick: Nanostructured Materials Vol. 11 (1) (1999), p. 125.

Acknowledgment This research was supported by the project GA 16-02430Y "Contemporary concepts of climatically active solar façades integrating advanced material solutions" supported by Czech Science Foundation and under the project No.
LO1408 "AdMaS UP – Advanced Materials, Structures and Technologies", supported by Ministry of Education, Youth and Sports under the "National Sustainability Program I".
Climate data processing for needs of energy analysis Advanced Materials Research, 2014, Vol. 1041, pp. 129-134 [8] Berger X, Cubizolles B, Donet I.
Quarterly Journal of the Royal Meteorological Society, 1963, Pages 339-348 [14] Runsheng Tang, Y.
Juráš, "Obtainable Method of Measuring the Solar Radiant Flux Based on Silicone Photodiode Element", Applied Mechanics and Materials, Vol. 824, pp. 477-484, 2016

Introduction Electrical discharge machining (EDM) is one of the most effective non-traditional material remove processes.
It’s widely used because it can process electrically conductive materials without considering their hardness.
The workpiece material, the dielectric medium, the charging voltage, the capacitance and the polarity were identified as some of the contributing factors.
The results show that polarity, material and dielectric medium have insignificant effect on D, Tu, Ti, and Imax while C and Uc have significant effect on them.
Kunieda: Journal of Advanced Mechanical Design, Systems, and Manufacturing.

Deans and Richards [7] suggested back face strain compliance technique for CT specimen and the technique have been widely used to evaluate crack length during material tests.
Kim et al.: The State-of-the-Art in Bridge Monitoring Systems and Related Techniques, (Korea Research Institute of Standards and Science, Rep. of Korea, 1998)
Kim: Damage evaluation for steel bridge member using compliance technique, Key Engineering Materials, Vols. 270-273 (2004), pp. 1610-1615
Richards: A simple and sensitive method of monitoring crack and load in compact fracture mechanics specimen using strain gages, Journal of Testing and Evaluation, Vol. 7, No. 3 (1979), pp. 147-154
Song: Back-face strain compliance calibration for the four-point bend specimen", KSME International Journal, Vol. 14, No. 3 (2000), pp. 314-319.

Manikandan1,a* 1Department of Chemistry, Faculty of Science, Annamalai University, Annamalainagar, 608 002, Tamilnadu, India. 2Department of Mathematics, Faculty of Science, Annamalai University, Annamalainagar, 608 002, Tamilnadu, India *Corresponding author.
Materials and Method This compound required chemicals and a solvent was of analytical group use in without additional purification.
The top results that pyrazole can be best material for NLO applications.
R Bhat, “Synthesis and Biological Evaluation of Certain Pyrazoline Deriva- tive of 2-(6-Methoxynaphthyl)-propionic Acid,” Indian Journal of Heterocyclic Chemistry, 8, 1, 1998, pp. 63-66
Indian Journal of Chemistry 49B, 351-355

Materials The starting materials were commercials high-purity chloride base materials of barium chloride dehydrate (BaCl2.2H2O), lanthanum chloride heptahydrate (LaCl3.7H2O), zinc chloride (ZnCl2), manganese (II) chloride dehydrate (MnCl2.2H2O), and ferric (III) chloride hexahydrate (FeCl3.6H2O) synthesized by Merck.
Consequently, it causes a decrease in the anisotropic constant of the M-type barium ferrites materials.
Acknowledgment This paper was conducted by research and development of magnetic Materials (DIPA, 2015-2019) in the Center for Science and Technology of Advanced Materials – National Nuclear Energy Agency, Indonesia.
Materials Sci.
H., Microwave Absorption Properties of Double-Layer RADAR Absorbing Materials Based on Doped Barium Hexaferrite/ TiO2/Conducting Carbon Black., Journal of Engineering.

Although there is no consensus, about which method and method of studying the material are the most reliable.
Analysis of radiological indicators of all studied materials of research was put through animal experiments.
Materials and Research Methods During the studies such X-ray methods of research were analyzed, as digital radiography, digital microfocus radiography, multispiral computed tomography, and x-ray densitometry.
Kazan Medical Journal. 2010; 91 (1): 44-48
Journal of Fundamental Studies. 2014; 7 (3): 468-472 [28] Dyachkova GV.

To obtain the optimal structure of the cement matrix [11-13], wastes from various industries are used: ground metallurgical slag, ash from burning brown coal, rice straw, husk, sunflower and materials exhibiting pozzolanic properties.
Physical and mechanical properties of concrete and consumption of materials per 1 m3
Srinivasan, Electrochemical Investigation of Corrosion Characteristics of Activated Ash and Slag Blended Cements, Materials Engineering, v. 14, pp. 261-283 (2003)
Pint, Study of cathodic reactions during intergranular corrosion of stainless steel, Science diary, v. 9 (33), p. 14 (2019)
Elichev, Formation of cracks in the cement stone of building structures, Journal of Science, v. 11 (11), p. 18 (2017)

Taking into account the set of physical and chemical properties of the given range of materials, tungsten most fully meets the requirements for high-temperature application in growing oxides and nitrides of certain metals with a melting point above 1800 oC.
Optical Materials, 134, Part A, (2022), 113176
Author links open overlay panel Journal of Crystal Growth.Volume 583(1), (2022), 126547
Problems of Atomic Science and Technology.. №1 [137] (2022) pp. 40-45
Problems of Atomic Science and Technology. №1 [125] (2020), pp. 60-63.