Search results

Silva1,a*,Tae jo Kim1 and Tong Yuan Koo3 1Department of Food Science, Nutrition and Health Promotion, Mississippi State University, Mississippi State, MS 39762, USA. 2 Department of Business Administration, TransWorld University, Touliu 640, Taiwan, ROC 3 Department of Industrial Engineering and Management, National Yunlin University of Science and Technology, Touliu 640, Taiwan, ROC a*jsilva@foodscience.msstate.edu, b*shin@twu.edu.tw Keywords: Enzyme Utilization, Food Industries, Response Surface Methodology, Catfish Nuggets Abstract.
Materials and Methods Materials.
Acknowledgment Approved for publication as Journal Article No.
Enzymic processing of marine raw materials.

By means of test data, CHEOL et al built up the intelligent models of material removal rate, surface roughness, grinding residual stress and so on for the grinding of cylindrical insert type [3].
Grinding Experiment Conditions of Spiral Bevel Gears Gear Material and Machining Process Here 20CrMnTi of spiral bevel gears was commonly selected in automobile gear material.
This showed that grinding temperature in this area already achieved ACcm of material or overtaked AC3.
Acknowledgements This project is supported by National Natural Science Foundation of China (Grant No. 51375161 and 51375160) , and Hunan Provincial Natural Science Foundation of China (Grant No. 13JJ6064).
International Journal of Refractory Metals & Hard Materials,2008,26:84-90

The maximum tensile strength (critical stress) of SS 304 material is ~ 515 MPa, [21] hence, the chamber can sustain ultra high vacuum.
This material is able to withstand high temperature and is vacuum compatible.
It is an interesting observation and has scope in fusion science and astrophysical research.
Acknowledgments We would like to thank Board of Research in Fusion Science & Technology (BRFST) for funding the project.
Chowdhuri: Asian Journal of Spectroscopy (2012), p. 231-238 [29] F.

The fuel of forest biomass power generation belongs to forest biomass material, thus makes much lower emission of SO2 and NOX, and creates almost zero emission of CO.
Furthermore, forest biomass material belongs to renewable energy, consequently, its emission and absorption of CO2 constitutes nature carbon cycling.If we do not take the CO2 emission from the acquisition and transportation links into account, its energy utilization can achieve the zero emission of CO2 , even negative emission.
At present, fire coals is the major materials for thermal power generation in China.
There is tremendous diversity of resources advantages among different regions in the vast China, thus the choice of form of clean energy power generation mainly depends on the local resource endowment and has little relation with environmental cost (it will create low environmental cost in all forms of clean energy power generation).Compared with other forms of power generation (especially the nuclear energy power generation),the forest biomass power generation has the advantages of the low risks, relatively simple devices, technology easy to be popularized and spread, and relatively cheaper materials.
[10] Zhu Gao, Jing Feng, Faxin Yu, Xiaoling Wang, Yi Yan, Tengyun Liu: Journal of Anhui Agricultural Sciences Vol.4 (2011), p.54-57 In Chinese

Materials and Research Methods During this work cases of patients with injuries of capsular ligamentous apparatus in orthopedical unit after arthroscopy were examined.
Publications of scientists were used that had been published in foreign and Russian peer reviewed journals.
The search was conducted through the RSCI (Russian Science Citation Index) and scientific electronic library eLIBRARY.RU.
III congress of Russion arthroscopic community: materials.
Dissertation by candidate of medical sciences.

Energy Efficiency of Single-family Houses in Serbia and Montenegro: Strategy for Upgrading the Performance of Existing Stock Saja Kosanović1,a, Dragan Komatina2,b*, Radovan Nikčević 3,c, Vera Murgul4,d, Nikolay Vatin5,e 1Faculty of Technical Sciences, 38200, Kosovska Mitrovica, Serbia 2Faculty of Architecture, 81000 Podgorica, Montenegro 3Independent Energy Efficiency Expert, 11000 Belgrade, Serbia 4,5St.
Introduction Achieving and constantly enhancing the energy end-use efficiency accounts for generally recognized objective and one of the key research topics in contemporary technical sciences.
Energy efficiency in existing single-family residential stock, from all above noted, may be considered as a significant current challenge for the two subject countries, while at the same time, for comparison, in developed western countries the attention already moves to other aspects of ecological friendliness of buildings, such as building materials or embodied energy [5].
Ecological assessment of building materials in Serbia: Constraints and possibilities (2014) International Journal of Contemporary Architecture The New ARCH, Vol. 1 (1), pp. 51-58
Development and competitiveness improvement of the construction sector in Montenegro (2014) Applied Mechanics and Materials.

While studies of eggshell concrete or rubberized concrete are present, it is a new approach to replace both cement and sand with waste materials.
Many researches also attempted to derive a more accurate expression especially when replacement materials were involved [41-42].
(Sciences Eng., 62 (2013) 95–101
Strukar, Recycled rubber as an aggregate replacement in self-compacting concrete-literature overview, Materials (Basel)., 11 (2018)
Rashad, A comprehensive overview about recycling rubber as fine aggregate replacement in traditional cementitious materials, Int.

Materials and Methods Z-ABS.
Dizon, “3D Printing Polymeric Materials for Robots with Embedded Systems,” Technologies, pp. 1–26, 2021, doi: https://doi.org/10.3390/technologies9040082
Advincula, “Additively manufactured high performance polymeric materials and their potential use in the oil and gas industry.” 2017
Hui, “Additive manufacturing (3D printing): A review of materials, methods, applications and challenges,” Compos.
Dunstan, “Materials mechanical size effects: A review,” Mater.

In addition, these materials have satisfactory mechanical properties [6].
Artificial hydroxyapatite is as good in biocompatibility as bio- logical hydroxyapatite, which is obtained from natural materials [13].
Thus, many works have been published concerning studies of biomagnetic materials for medicine.
Chemical composition of the ferrite and the technological and magnetic parameters of powder materials at 300 K No.
Olkhovik, in Proceedings of the International Conference “Functional Materials,” Partenit, Crimea, Ukraine, October 1–7 (2007) 503

These luminescent materials may be applicable for scintillators.
These kind of luminescent materials can be used for white light-emitting diodes (LEDs).
Light: Science & Applications 2 (2013) e50- e50(8)
Schmidt, inorganic Luminescent Materials: 100 years of Research and application, J.
Metselaar, Luminescence Properties of Terbium, Cerium, or Europium doped α-Sialon Materials, J.