Search results

It provides a certain reference for the reduction of noise and vibration of car’s air conditioning and refrigeration system.
Through the interior noise test in different conditions, the octave analysis, according to the formula: [5],Thus three point total sound pressure level of data are calculated, such as table 1.
Therefore, finding out the vibration noise transmission way in order to have a purpose for damping noise reduction.

So the cooling and filling time is directly proportional to the reduction of production cost. 3D model of the mould was created in Autodesk Inventor Proffesional software and then solidification of material was simulated in Autodesk Moldflow Insight software.
a) b) c) d) Fig.5 Time of mould filling analysis Fig.6 Summary of mould filling times for individual alternatives [s] Cooling time of squirt product is the longest period in a process of injection moulding; therefore it is necessary to highlight the importance of this factor, because the shortening of the time needed for squirt product cooling is directly proportional to the reduction of production costs.
Materials Vol. 440 (2013), p. 188-193 [4] Dobransky, J.Baron, P.: Application of Computer Simulation in the Manufacture of Thermoplastic Products by Injection Molding, In: ICCEE 2010 3rd International Conference on Computer and Electrical Engineering proceedings, Chengdu, China, (2010), p. 628-631 [5] Stancekova, D. et al.: Diagnostic of the Tools for Bulk-Forming and Renovation by Milling, In: ICET 2013 Proceedings of International Congress on Engineering and Technology, Dubrovnik, Croatia,(2013), p. 245-250 [6] Ress, H., C.: Selecting Injection Molds – Weighing Cost versus Productivity,Hanser Publishers, 2006 [7] Goban, J.: Optimization of mould cooling system for the plastic injection technology, Doctoral thesis, FMT TUKE, Presov, 2013 [8] Spisak, E., Majernikova, J.: Analysis of variance of mechanical properties of sheets as the input parameters for simulation of processes, In: ActaMetallurgicaSlovaca, Vol.18, no.2-3, (2012), p. 109-116 [9] Mares, A., Senderska, K., Kovac, J.: Data

Compared to Si, the SiC freewheeling diode produced over twenty times lower reverse recovery charge leading to approximately a factor-of-four-reduction in turn-on loss.
Finally, a physics based circuit model has been developed and verified against measured performance data.
Overall the JBS parts demonstrated a 20x decrease in reverse recovery charge and about 4x reduction in turn-on loss.

In pipeline leak detection, collected fault signal will inevitably influenced by all kinds of industrial noise, sometimes even the useful signals submerged by the noise, so before data analysis, we shall be carried out in a first filtering processing.
The experimental data shows that Kalman filter is an efficient recursive filter, it can estimate the states of the dynamic system from a series of contains noise measurement.
The program diagram of realizing kalman filtering algorithm On the front panel of a data processing module of kalman filter, it is placed two windows to display waveform, respectively used to display the original pressure signal and the pressure signal with kalman filter processing, as shown in figure 3,4.
The pressure signal with kalman filter processing From the diagrams above, we can be seen that the data becomes smooth clearly compared with the original data after processing with the kalman filter, and the filtering effect is obvious.
Advanced Digital Signal Processing and Noise Reduction, Electronic industry press, 135-140.

The data presented to evaluate friction and wear characteristics are coefficient of friction (μ), wear scar diameter (WSD), flash temperature parameter (FTP) and viscosity index (VI).
Fig. 3(a) showed the maximum reduction of 6.71% of WSD for 5% JO added lubricant followed by 3.89% and 2.89% for 3% and 4% JO added lubricant respectively as compared to reference lubricant.
Similarly as compared to reference lubricant, Fig 3(b) showed the maximum reduction of 6.44% of WSD for 5% JO added lubricant followed by 4.37% and 3.74% for 4% and 2% JO added lubricant respectively.
· As compared to reference lubricant, 5% JO added lubricant showed maximum reduction of 6.71% WSD and 6.44% WSD at 15 and 40 kg load respectively

A data acquisition card is used to obtain the real-time unbalanced signal.
The data collection of this system is used the Taiwan Advantage 4711A type data acquisition card.
The hydraulic system is controlled by the voltage signal given by the data acquisition.
Some actual experimental data are shown in Tab. 1.
Fig.2 Flow chart for automated balancing machine Fig.3 Prototype of automatic balancing machine It shows that the measured data of the automated balancing machine agree with the experiment data in Tab.1.

The three most issue in identification are data, model and the estimation method [2].
To have a successful identification, we should be able to collect data in a wide range of helicopter operating points.
By this controller, data collection is possible using proper excitation signal.
Low sampling time cause loss of data.
The excitation signal designed to make rich input-output data.

Energy demand reduction in buildings is an important measure to achieve climate change mitigation.
Therefore, a reduction of the specific energy demand of buildings and increased use of renewable energy are important measures of climate change mitigation.
The calculated data from the 2-D method represents heat loss for all details.

In existing multi-rotor aerial robot design, all four or eight rotors usually necessary to provide lift, while also should to change their force to control the attitude of the robot at the same time, which brings a reduction in efficiency.
Figure 3 shows the acceleration obtained through GPS data.
Az Fig.3 Acceleration obtained by the GPS data The acceleration from SINS accelerometer is the actual feel of aerial robot’s acceleration.  
The discrete point data represents the measurement of the combination algorithm, witch consistents with the actual real value.
Fig.5 Four Controllable motion states of Aerial Robot Aerial Robot navigation and control hardware system mainly includes sensor module, power supply module, data processing module and communication module. 

When the study the friction parameters in conditions of a low hearth of plastic deformation, the correspondence of the obtained results and practical data was discovered.
When the study of the wire drawing process in conditions with a high hearth of plastic deformation the discrepancy between the calculated and experimental data was revealed, that can be explained by conditions of plastic flow in the deformation zone.
Industrial enterprises carry out wire drawing with small relative reductions, close to 20%.
While the study of the friction parameters in conditions of a low hearth of plastic deformation when wire drawing, the correspondence of the obtained results and practical data was established.
While the study of the wire drawing process in conditions with a high hearth of plastic deformation the discrepancy between the calculated and experimental data was revealed, that can be explained by conditions of plastic flow in the deformation zone.