Search results

Quantitative Concept for Morphological Stability Analysis of LiquidSolid Interface in Rapid Solidification of Dilute Binary Alloys Mohamed DRAISSIA LM2S, Lab.
For dilute alloys, the solid-liquid interface growth velocity is increased leading to rapid solidification, as for pure metals [6].
(iii) The atomistic models based on capillarity strains explained well the plane-front growth observed in rapidly solidified binary alloys.
[2] J.W.Rutter, B.Chalmers, Canadian Journal of Physics, 34 (1953) p.15
[7] M.Draissia, M.Y.Debili, Central European Journal of Physics, 3(3) (2005) p.395

This study aimed to explore the possibility of using a dielectric glass to connect a dielectric ceramic resonator to a dielectric ceramic support, in order to make miniaturized microwave filters characterized by higher temperature and environmental stability and low dielectric loss.
The compound of NdAlO3 was synthesized from Nd2O3 and Al2O3 powders based on the right molar ratio and by calcination at 1300oC for 3 hours.
Iddles: Journal of the American Ceramic Society Vol. 89[7] (2006), p. 2063
Wang: Journal of Central South University of Technology (English Edition) Vol. 18[5] (2011), p. 1359
Li: Journal of Alloys and Compounds Vol. 490[1-2] (2010), p. 204

HA is one of these Ca-P compounds and major mineral constituent of vertebrate bone and teeth.
Dorozhkin, Calcium orthophosphate coatings on magnesium and its biodegradable alloys.
Journal of Alloys and Compounds, 661 (2016), pp.251-256
Jiang, Structure and properties of compound coatings on Mg alloys by micro-arc oxidation/hydrothermal treatment. 
Journal of Alloys and Compounds, 633(2015), pp.435-442

It is expected that the addition of BaTiO3 on ceramic alloys consist of BiFeO3 and BaTiO3 can improve the electrical properties of the ceramics and finally it improves the multiferroic properties of the material.
The formation of alloying ceramics between BiFeO3 and other compounds can increase piezoelectric and ferromagnetic response of multiferroic materials.
The other compounds can be BaTiO3 as alloying ceramic with BiFeO3[3] and doped BiFeO3-BaTiO3[4,5,6].
[3] Q.Pan, B.Chu, Enhanced magnetoelectric response in bismuth-deficient BiFeO3-BaTiO3 ceramics, Journal of Applied Physics, 125, 154102 (2019)
Series: Journal of Physics: Conf.

Amarasinghe, Journal of Alloys and Compounds, 708 (2017) 67-72, http://dx.doi.org/10.1016/j.jallcom.2017.03.003 [2].
Thermal Plasma Spheroidization of High-Nitrogen Stainless Steel Powder Alloys Synthesized by Mechanical Alloying // Metals and Materials International. 2018.
Lisenkov, Plasmachemical Synthesis of Aluminum Based Nitride Compounds in Vacuum Arc Discharge Plasma, Technical physics letters, 38 (2012), 938-940 [17].
Fabrication of spherical high-nitrogen stainless steel powder alloys by mechanical alloying and thermal plasma spheroidization // AIP Conference Proceedings. 2018. 1946, 020001; doi: 10.1063/1.5030305 [19].
Fabrication of the Nb–16Si alloy powder for additive technologies by mechanical alloying and spheroidization in electric-arc discharge thermal plasma // Russian Journal of Non-Ferrous Metals, 2018, Vol. 59, No. 6, pp. 671–676.

The aim of this paper is to producing CoCrMo foam that will be given to consider the properties of CoCrMo foam after sintering process.
CoCrMo alloys for, orthopaedic implants are primarily in the cast or wrought forms, with similar chemical compositions based on American Society for Testing and Materials (ASTM) standards [5].
The wrought CoCrMo alloys exhibit superior mechanical and chemical properties compared with the cast alloys due to a finer grain size and more homogenous microstructure [6].
In this study, the CoCrMo powder was tested with XRD to make sure the compound that is present is the same to sample after the sintering process [11].
Mohamad Nor, “Development and Characterization of Titanium Alloy Foams”, International Journal of Mechanical and Materials Engineering (IJMME), Vol. 5, No. 2, 244-250 (2010).

Nanocrystalline Fe40Co60 alloys elaborated by mechanical alloying (MA) in a high-energy planetary ball mill (RETSCH PM400) were dispersed into commercial epoxy resin matrix to form thin polymer nanocomposites.
Materials and Methods In this study, we report on the structural and the microwave absorption properties of nanocrystalline Fe40Co60 alloys.
Several techniques are available to produce nanocrystalline alloys (crystallites size less than 100 nm).
Kulik, Phase transformations during mechanical alloying of Fe-50%Al and subsequent heating of the milling product, J. of Alloys and Compounds, vol. 424, Issues1-2 (2006) p.119-127
Suryanarayana, Mechanical Alloying: a novel technique to synthesize advanced materials, Official Journal of Cast Research, vol. 2019 (2019)

The aim of this study was thus to investigate the fine detail of microstructures of Cu-alloyed ductile iron treated by the two-step austempering process.
Although most of the alloys used in previous studies [8-15] were unalloyed and Ni-Mo alloyed ductile irons, the Cu-alloyed iron was chosen in this study since it is cheaper and shows high potential to be a composition for commercial ADI [6,16].
The microstructures of iron alloys were observed using the optical microscopy, scanning electron microscopy (Jeol-JSM8500) and transmission electron microscopy (Jeol-JEM 2010) techniques.
Chemical composition of iron alloy [weight %] C Si Cu Mn Mg P S Fe 3.52 2.61 0.75 0.32 0.042 0.015 0.001 Bal.
Kiani-Rashid: Journal of Alloys and Compounds Vol.474, No. 1-2 (2009), p. 490 [16] U.

The aim of this study is to investigate the mechanical properties of ductile iron after treatment with two-cycle heat treatment processes which modified from austempering.
The process is most preferable tool nowadays since it can improve mechanical and physical without changing the product shape as well as addition of alloying element [2-4].
Fatahalla, Journal of Materials Science 38 (2003) 351– 362 [2] Ali M.
Villanueva, Journal of Achievements in Materials and Manufacturing Engineering 33/2 (2009) 150-158
Kiani-Rashid, Journal of Alloys and Compounds 470 (2009) 323–327 [9] Yusuf Kayali, Sukru Taktak, Sinan Ulu, Yilmaz Yalcin, Materials and Design 31 (2010) 1799-1803 [10] B.

The paper aims the determination of the friction force by means of external friction stress, at the severe plastic deformation processing using cyclic closed-die forging method.
Copper and its alloys multiaxialy forged have a wide range of utilities because the high mechanical characteristics obtained, [10, 11].
Gubicza: Journal of Alloys and Compounds 509 (2011), p. 3522
Valiev: Journal of Materials Research 17 (2002), p. 5