Search results

(i=1,2,3,4,5) stretchable struts; (i=1,2,3,4,5) universal joint; (i=1,2,3,4,5) swivel joint Fig.1 A 5-sitvel-5-strut machine Working space The description of working space.Working space is an important target of a 5-axis-5-swivel parallel machine tool.
So the working space can be indicated by the cap of Wt (t=1, 2)
References [1] Wang Jinsong, Huang Tian.
J. of Robotic Systems, 1993, 10(4): 463-479
S.Wang.CIRP Annals, 1998, 47(1): 347-351

Figure 1.
Crops Prod., 32,1 (2010) 7–12
Technol., 50,1 (2006) 132–140
J., 148,2–3 (2009) 473–479
Water Air & Soil Pollution, 214,1 (2011) 107–117

Weigh ZnO, MnCO3 and H3BO3 and puts them in beaker B, and mix them dissolved with HNO3 of 1:1.
Compare with the results of literature [1], this samples have lower anneal temperature and shorter anneal time, and the effective excitation wavelength expanded 20 nm.
References [1]Cai J J, Wang Y, Pan H H, Zeng Q G and Hu S J.Preparation and Photoluminescence of Green Zn2SiO4 :Mn2+ Phosphor by Sol-gel Method[J]. 2010, 96(2-4):171-175
Mater. , 1999, 14(3):479-482
Lumin., 2007, 28(1):126-130

Introduction The magnesium alloys such as AZ91, AM60 and ZK60 are used to study semisolid forming (SSF) [1-4].
Its chemical composition is listed in Table 1.
In DSC analysis (Figure 1), the range of melting temperature is between 435.5℃ and 550℃.
References [1] Y.
Forum Vol. 475-479 (2005), p. 537 [11] G.

The addition of Nd2O3 decreases the mullite formation temperature to 1200 ˚C. 1.
The proportion of cordierite and mullite was 1:0 and 7:3 (labelled as C and A0, respectively).
The results are shown in Fig. 1.
References [1] I.
Soc. 22 (2002), p 479 [8] T.

Fig. 1 shows j-V plots measured at different light intensities for 1M HCl at a scan rate of 10 mV/s.
Figures 2A-B show AFM images for a 10 nm etched Ge surface in 1 M HCl and 8 M HCl solutions.
Height resolution is 20 nm and the image size is 1 x 1 µm.
References [1] R.
Pillarisetty: Nature 479 (2011), p. 324-328

Fig. 1 Schematic drawing of the apparatus for separation experiment.
The result of separation experiments were summarized in Table 1.
Conclusions 1.
References [1] H.
Kagawa: Material Science Forum, 475-479(2005) 2559-2562 [12] T.

Fig.1.
The pull force F1 on the cable is calculated by (1)
Substituting into (1) and (2), we can get T= 0.314Nm.
References [1] S.
, 1993, pp.474-479

So the interfacial reaction between molten slag and refractories can be inevitably affected by EMF [1,3].
Mass ratio of CaO to SiO2 in the slag is about 0.8 and its chemical composition was shown in Table 1.
Conclusions 1) In EMF, Mn-doped MgFe2O4 spinels would be generated and distributed in erosion layer.
References [1] L.B.
Tech. 5 (2008) 469-479

Fig.1 Typical full-sized ballast particle [6,7] Particles Modeling.
Typical real ballast particle is shown in Fig. 1.
The parameters selected in this simulation had been mentioned in reference literatures [7], and the used main parameters are shown in table 1.
Geotechnical Engineering, v 159, n 1, p 35-48, January 2006 [3] Ferellec, J.
Vols. 479-481, p1395-1398